Post Style Guide On that Fits Tri-Toon Pontoon Boat Trailer

Question

Question:

Will these fit on a pontoon tri-toon boat trailer

asked by: Eddie M

0

Expert Reply:

We actually have a boat guide on that was designed for pontoon boat trailers with the part # CE27670 which is better designed for the frame styles of pontoon boat trailers. The # CE27760 wouldn't work as it would need a different frame style.

expert reply by: Jameson C

0

Answer 1

There is an upright which may work for you, the Replacement Upright for CE Smith Bunk-Style Guide-Ons for Boat Trailers - Lanced - 39" #CE27605PG. This upright has a bottom leg of 23 inches, and is a replacement for CE Smith Post-Style Guide-Ons…

view full answer...

Answer 2

We have a couple of great options for pontoon boat guide-ons. First, if you want to go with a roller-style we have #CE27672. The rubber rollers are designed so that they won't scratch the boat. If you like the bunk style we have #CE27671. The…

view full answer...

Answer 3

The CE Smith Roller-Style Guide-Ons for Boat Trailers part #CE27610 are galvanized which is a zinc coating. This coating will do a great job of resisting rust so you don't need to worry about painting them. In fact, paint does not adhere to…

view full answer...

Answer 4

Yes, the CE Smith Bunk-Style Guide-Ons for Boat Trailers - 60" Long - 1 Pair #CE27600 can work on the inside of a pontoon boat. Based on the photo you may prefer the CE Smith 90-Degree Bunk Board Guide-On Kit #CE27600K90 which will includes…

view full answer...

Answer 5

The correct size of bunk boards for your pontoon boat trailer is going to vary depending on configuration. Generally speaking, you will want the horizontal bunk boards to reach from the transom edge to the hull. Most people will then run two sets of…

view full answer...

Answer 6

We sell replacement mounting hardware for the CE Smith roller guide-ons part #CE27610 with the part #CE11451-A.

view full answer...

Answer 7

Yes, you can use the CE Smith Bunk-Style Guide-On Kit #CE27600K90 for the inside pontoons on your cradle lift. You will want to ensure that the uprights will not interfere with anything under your boat when on the lift. The uprights are 19-3/4"…

view full answer...

Answer 8

The CE Smith Post-Style Guide-Ons #CE27670 that you referenced are 22 inches tall including the mounting brackets. Basically the top of the will sit exactly 22 inches above the frame of the trailer it installs onto. The PVC portion does not float or…

view full answer...

Answer 9

The PVC pipes of the CE Smith Post Guide Ons #CE27670 that you referenced do not spin. They actually have a slit cut into the bottom of them that lines up with a groove on the elbow fitting that prevents them from spinning. These aren't intended…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Post Style Guide On that Fits Tri-Toon Pontoon Boat Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching