Draw-Tite Trailer Hitch for 2010 Mazda 3 Sedan

Question

Question:

Will this hitch fit a 2010 Mazda 3 sedan? Are hatchback/speed3 fitments different from sedans?

asked by: Mike D

0

Expert Reply:

I do have a solution for you, however the Draw-Tite # 24843 will not fit a 2010 Mazda 3 Sedan. The hitch to fit your Mazda 3 Sedan is the Curt # C11393.

The # 24843 will fit the Speed 3 and hatchback models but not the sedan.

expert reply by: Bryce D

0

Answer 1

I checked with the manufacturer for you, and can confirm that the Curt Trailer Hitch #C11393 will fit your 2012 Mazda 3 Sport sedan with dual exhaust. The exhaust sits far enough back that there won't be any type of interference with the hitch. I…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 5

I'm happy to say that there is indeed both a trailer hitch and trailer wiring for your 2024 Chevy Trax. The fits for both parts on your '24 Trax are the following: - Curt Trailer Hitch Receiver #C75VV - Tail Light Converter with 4-Pole Flat…

view full answer...

Answer 6

The Curt Trailer Hitch Receiver #C11393 will not contact the exhaust on your 2012 Mazda 3 sedan.

view full answer...

Answer 7

I can recommend a trailer hitches for your 2012 Mazda 3 i Grand Touring. If your Mazda is a Sedan use the Curt hitch part #C11393. If it's a hatchback use the Draw Tite part #24843. Both of them install faily easily with included bolts. I've…

view full answer...

Answer 8

We have everything you are looking for, but I must warn you that Mazda does not recommend towing with this vehicle, so you would be doing so at your own risk. The other complication is that there is no stated towing capacity for your vehicle because…

view full answer...

Answer 9

The Draw-Tite Sportframe Trailer Hitch Receiver you referenced, part #24816, fits the Mazda 3 up through model year 2009, but I can tell you the correct hitch fit for your 2012 Mazda 3 as well. You can use the link provided to see our main page for…

view full answer...

Answer 10

For a carbon frame bike a hitch bike rack that holds the bike by just the tires is the only safe option. Trunk racks all touch the frame which is something you need to avoid with carbon frame bikes. So for a hitch you'd need the Draw Tite #24843…

view full answer...

Answer 11

You actually will want to open the end of the crossbar like in the picture I attached and then slide the strip down the end of the crossbar. You would not want to try and press it in. Hope your thumb feels better!

view full answer...

Answer 12

There are specific fits for a 2010 Mazda 3 for the hatchback vs. the sedan. If you have a sedan, I recommend the Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4" #C11393. If you have a hatchback, I recommend the Draw-Tite Sportframe…

view full answer...

Draw-Tite Trailer Hitch for 2010 Mazda 3 Sedan

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching