Fastway e2 Weight Distribution Hitch Spacer Washers Minimum and Maximum For Hitch Head Angle

Question

Question:

I am currently towing a 34 ft travel trailer 6200 dry weight, 7700 total weight passenger weight, gas, truckbed and inside camper with my 2019 Ram 1500 Crew Cab 8200 towing capacity. Trailer hitch weight is 710 but with additional weight in trailer and truck, its prob in the 900-1000 range. I had a prior travel trailer which was 2k lbs less and had the Fastway e2 800/8000lb weight distribution system towing with the same Ram truck. On my first trip with the new camper and above setup, I had several inches of squat. It hauled pretty decent but in some wind and getting passed by trucks, I felt slight movement. I then purchased Timbren Rear Suspension Enhancement System ITEM # TDR1500DQ and Replacement Round Spring Bar for Fastway e2 Weight Distribution Systems - 1,000 lbs TW ITEM # FA94-02-1099. Attached are pics of the new setup and while the bars are not fully parallel with the frame L bracket is 1inch lower than hitch connector, it sits much better than prior. I did notice the trailer installer used 3 spacer washers and I am not sure if adding more will help. I also tried adjusting the L bracket to get the bar arms level but that increased the downward pitch. Interested in your thoughts on the above setup. Please see pics. The pic of truck bed with cargo was pre Timbrens and 800lb bars. All other pics are based on Timbrens installed and 1000lb bars. Thank you. Truck Bed Empty w Trailer With OUT trailer attached 36 3/4" With OUT WD 37" WITH WD 36 3/4" Truck Bed w 250 lbs of cargo With OUT trailer attached 36 3/4" With OUT WD 37" WITH WD 36 3/4"

asked by: Kevin D

1

Helpful Expert Reply:

It looks to me that you will want additional spacers to provide better weight distribution on your 2019 Ram 1500. The Fast Way e2 Weight-Distribution Hitch # FA94-00-1061 is capable of having up to 9 spacers to provide the correct pinion angle on the hitch head and provide adequate weight distribution. As you have done with the measurements that you have on the front of your Ram you can also do the same process on the rear axle. This will help you to dial in the exact amount of spacers to use.

Per the manufacturer instructions which I have linked below they recommend a minimum amount of 5 spacers to be used.

expert reply by: Bud M

1

Customer Image 1
(click to enlarge)

Customer Image 2
(click to enlarge)

Customer Image 3
(click to enlarge)

Customer Image 4
(click to enlarge)

Customer Image 5
(click to enlarge)

Answer 1

If your light truck tires are rated for 2600 lbs each then towing the 7,000 lb trailer is fine as long as the trailer's weight is less than the Cadillac's towing capacity. The trailer has its own tires so the weight of the trailer is…

view full answer...

Answer 2

I do have an option for you but they do not make a set of rear airbags for your 1993 Ford E-150. I recommend using the Timbren Rear Suspension Enhancement System part #TFER15087 instead which will also not change your ride height. The Timbrens will…

view full answer...

Answer 3

You should add one spacer washer at a time with the Fastway e2 Weight Distribution System #FA92-00-1000 as there is not a specific formula regarding one washer equaling a certain measurement. The reason for this is that there are too many variables…

view full answer...

Answer 4

It sounds like the remains of a double lip seal. Was it like a rubber o-ring with a metal spring around it? You are going to have to replace the seal so I would just disregard the sleeve. It would go on the outside of the rubber lip though. I…

view full answer...

Answer 5

Actually, there's a little more to it than that. The magnets on the #K23-478-479 are a little different, but the primary difference is the mounting bolt pattern. On a typical 3500 lb brake assembly, the mounting studs will all be 2-7/8…

view full answer...

Answer 6

The Kenda Karrier ST225/75R15 Radial Trailer Tire - Load Range E, Part #AM10303 is rated at a max load of 2,830 lbs at 80 psi. Almost all tire manufacturers advise running tires fully inflated to the recommended PSI when the tires are cold. The only…

view full answer...

Answer 7

The Westlake ST225/75R15 Radial Trailer Tire w/ 15" Silver Mod Wheel - 6 on 5-1/2 - Load Range E #LHAW124 should be inflated to 80 psi when cold. It is great that you do use a TPMS like #TST-507-FT-4-C that monitors both tire pressure and…

view full answer...

Answer 8

If the trailer is less than 1 inch off of being perfectly level either up or down then it will be perfectly fine. Having it slightly higher would be better because presumably the tongue weight of the trailer will pull it down a little. You could also…

view full answer...

Answer 9

The Solera Awnbrella Support Kit for 8' Projection RV Awning - 3 Pack #LC362237 is designed to work with most 8' projection awnings that are between 14' and 18' wide. Though I could not find anything about these being used with a…

view full answer...

Answer 10

When it comes to installing your Timbren Suspension System #TFR350SDJ on your 2022 Ford F-350 Super Duty, per the manufacturer you can install them with your rear sway bar already being attached, and there will be no problem. I have attached a…

view full answer...

Answer 11

The Coil SumoSprings #CSS-1094F are designed to add additional support to the front. Since you don't have a front load on your 2022 Toyota Tundra I don't think this will be necessary or make a real difference. As for the Timbren #T45MR, I…

view full answer...

Answer 12

I spoke to my contact at Fastway and he informed me that on a shorter wheelbase vehicle like your 2003 Ford Expedition a good starting point would be 5-6 washers, but the reason they do not list a recommended amount in the instructions is because the…

view full answer...

Fastway e2 Weight Distribution Hitch Spacer Washers Minimum and Maximum For Hitch Head Angle

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching