Inner Sleeve Material On Yates Spool Roller # YR4163-4P

Question

Question:

Does this model have a inner plastic sleeve?

asked by: Dan U

0

Expert Reply:

The Yates Spool Roller for Boat Trailers # YR4163-4P has a polyethylene inner sleeve to allow for the roller to easily turn on the 1/2" shaft.

expert reply by: Bud M

0

Answer 1

A TPR roller like the #YR500YW-6P is going to be better than PVC. PVC is a cheaper product. TPR has the properties and performance of both PVC and rubber while having a higher tensile strength so it is going to be the most durable. I don't have a…

view full answer...

Answer 2

The CE Smith Side Angle Mounting Brackets for Boat Trailer Rollers - Galvanized Steel - 1 Pair #CE10211G have holes that are 2-1/4 inches on center and 1-1/4 inches on center in the other direction. I've attached a photo to assist as well as a…

view full answer...

Answer 3

I have attached a picture that shows the dimensions of the CE Smith Spool Roller Assembly for Boat Trailers item #CE32100G. It measures 2-1/4-inches from the bottom of its mounting plate up to the center of the rubber roller. Overall width is…

view full answer...

Answer 4

We do have some of the replacement rollers that will work for your vintage 1965 boat trailer, but we do not have some of the rollers you asked about. Thank you for the dimensions. For the very front keel roller I recommend part #YR5213-5. This…

view full answer...

Answer 5

The Replacement Pal Nuts #CE10800A will just need to be pressed onto the 1/2" diameter shaft for your roller. You may need to boop them on with a rubber mallet if they don't go on easily.

view full answer...

Answer 6

The Yates Endcap for Boat Trailer Rollers part #YR130-4 will work great with the Yates Bow Roller for Boat Trailers part #YR300BLK. If you need a roller shaft as well, I recommend the Roller Shaft with Pal Nuts part #CE10701A.

view full answer...

Answer 7

In order to find the correct replacement spool roller for your boat trailer, you would need to measure from the inside of each mounting bracket. The 4-1/2" long measurement that you provided is not common and we would not have anything that…

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 11

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 12

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Inner Sleeve Material On Yates Spool Roller # YR4163-4P

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching