Dimensions of CE Smith Side Angle Galvanized Mounting Bracket

Question

Question:

In your QandA, I found the measurement from the mounting surface to the center of the hole in the longer side of this bracket, but what about the measurement from the mounting surface to the hole center if the part is used in the other orientation? I need a bracket like this, but in a different application, not with a roller.

asked by: T L

0

Expert Reply:

The CE Smith Side Angle Mounting Brackets for Boat Trailer Rollers - Galvanized Steel - 1 Pair # CE10211G have holes that are 2-1/4 inches on center and 1-1/4 inches on center in the other direction. I've attached a photo to assist as well as a photo with other dimensions to assist.

expert reply by: Jason S

0

click to enlarge

Answer 1

A TPR roller like the #YR500YW-6P is going to be better than PVC. PVC is a cheaper product. TPR has the properties and performance of both PVC and rubber while having a higher tensile strength so it is going to be the most durable. I don't…

view full answer...

Answer 2

I went out into our warehouse and pulled a CE Smith Side Angle Mounting Brackets #CE10211G to get some measurements for you. Check out the picture I attached to see them all.

view full answer...

Answer 3

I went out to the warehouse and pulled the Universal Roller Brackets, #MBSPB, to take some measurements for you. From the center of the hole to the nearest edge of the flat mounting surface measures 2-11/16 inches. The bracket is 1/8 inches thick…

view full answer...

Answer 4

I have attached a picture that shows the dimensions of the CE Smith Spool Roller Assembly for Boat Trailers item #CE32100G. It measures 2-1/4-inches from the bottom of its mounting plate up to the center of the rubber roller. Overall width is…

view full answer...

Answer 5

The Yates Spool Roller for Boat Trailers #YR4163-4P has a polyethylene inner sleeve to allow for the roller to easily turn on the 1/2" shaft.

view full answer...

Answer 6

A keel roller is not designed to carry the bulk of a boat's weight. That is the job of the bunks, whether they are wobble roller bunks like yours, standard roller bunks or carpeted bunks. Also, it is not a good idea to mount any of these boat…

view full answer...

Answer 7

We do have some of the replacement rollers that will work for your vintage 1965 boat trailer, but we do not have some of the rollers you asked about. Thank you for the dimensions. For the very front keel roller I recommend part #YR5213-5. This…

view full answer...

Answer 8

Fulton no longer makes the T1602 winch, it's been replaced by the F2, part #FW16000101. If you're happy with the way your old one performed, it would be good replacement. If you wanted to go up to an 1800 lb capacity, you could use the Fulton…

view full answer...

Answer 9

From past customers we have found that the TeeNee trailers use a three inch keel roller like the part #YR300Y. That being said I would need to see a picture of your setup to give you the best options we have. I did some research on your Tee Nee…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 12

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Dimensions of CE Smith Side Angle Galvanized Mounting Bracket

Product Page this Question was Asked From

Continue Researching