Fit of Curt C60633 Custom Under-Bed Gooseneck Hitch on 2019 Ram 2500

Question

Question:

Will this hitch fit my 2019 Ram 2500 short bed diesel?

asked by: Alan C

1

Helpful Expert Reply:

The Curt # C60633 Custom Under-Bed mount gooseneck hitch you'd looked at is compatible with your 2019 Ram 2500 Diesel as long as it doesn't have the factory puck system.

If you'd like to install a 7-way trailer connector in the truck bed so you don't need to run the trailer connector cable up and over the tailgate, you can install one using part # 41157.

I've linked to install videos for the hitch and the trailer connector/harness I recommended.

expert reply by: Mike L

1

Answer 1

I reached out to my contact at Curt and the Curt Custom Underbed OEM-Style Gooseneck Trailer Hitch - 35,000 lbs #C60633 you were looking at is confirmed to fit your 2021 Ram 3500 Long bed as long as it does not have the OEM towing prep package. To be…

view full answer...

Answer 2

When a camper is loaded on a pickup truck bed there will be a gap between the truck bed rails and the underside of the camper as you show in your photo. No worries there. For your camper tie-downs, it loos as though you have attached the rear ones…

view full answer...

Answer 3

I reached out to my contact at Curt and the center of the gooseneck hole of the Curt Custom Underbed OEM-Style Gooseneck Trailer Hitch - 35,000 lbs #C60633 will be right at 34-3/4" back from the front of the 6-1/2" bed in your 2020 Ram…

view full answer...

Answer 4

We offer the Reese 9485 as our own unique part number, #DT89MR, as well as the Curt #C60633 or the B&W #BWGNRK1320 which will all fit. If I personally had to choose between the two, I'd go with the B&W because I prefer the side-latch…

view full answer...

Answer 5

Yes, the Curt Custom Underbed OEM-Style Gooseneck Trailer Hitch - 35,000 lbs item #C60633 will fit all models of the 2022 Ram 2500 so long as they do not have the factory towing prep package. I have linked an installation video. I recommend adding…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 11

Hey Ted, so if you look in the bed of your truck and see 5 holes/pucks that would mean you have the OEM prep. I'd assume if you had it you'd have seen them by now. If you had it you'd only need a ball like the part #C60618. If you…

view full answer...

Answer 12

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...