What Is The Distance Between The Mounting Holes On The Buyers Products 5/8" D-Ring 337B40MP?

Question

Question:

please provide me with the distance of center hole to center hole.

asked by: Todd W

0

Expert Reply:

The mounting holes on the Buyers Products 5/8" Forged D-Ring With 4-Hole Integral Mounting Bracket # 337B40MP you were looking at are 5" apart on center as shown in the included diagram.

I included a video of Adam installing the # 337B40MP on a trailer for you to take a look at.

expert reply by: Samuel C

0

Mounting Hole Dimensions of # 337B40MP
(click to enlarge)

Answer 1

The Buyers Products 5/8" Forged D-Ring #337B40MP has a working load limit of 6,130 pounds. The break strength data was not provided. Usually the working load limit is a third of the break strength but again the exact figure is not provided. The…

view full answer...

Answer 2

The inner measurement of the Brophy D-Ring Tie Down Anchor item #DR01 is 2 1/4". I have attached a diagram with the measurement.

view full answer...

Answer 3

The mounting brackets of the Buyers Products 5/8" Forged D-Ring With 4-Hole Integral Mounting Bracket #337B40MP that you referenced are 6 inch by 1 inch. I would recommend using these on the other side of your truck bed when attaching these to a…

view full answer...

Answer 4

You'll need to start by having a new hanger welded on since it looks like the hanger towards the front of the trailer has been broken off. Once that's welded in place you can then install a new leaf spring. To determine the correct…

view full answer...

Answer 5

I went out to the warehouse and pulled hanger kit #APS1 to measure the hangers for you. The larger hangers measure 3 inches long, 2-5/16 inches wide, and 2-1/8 inches tall overall. The smaller hangers are 2-1/8 inches long, 1-13/16 inches wide, and…

view full answer...

Answer 6

I attached the chart you referenced and it states that when you use a #e54SR spring with a hanger kit part #APS3 the hanger distance should be 24-7/8 inches. The length of a spring when new and not installed on a trailer will be slightly shorter than…

view full answer...

Answer 7

The Single-Axle Trailer Hanger Kit for Double-Eye Springs - 1-1/2" Front, 1-1/4" Rear #APS2 will work well for your 1-3/4 inch wide leaf springs. Double eye springs are the style have both the bolt in the front and rear and are more common…

view full answer...

Answer 8

When choosing between the Single-Axle Trailer Hanger Kit for Double-Eye Springs part #APS1, part #APS2, and part #APS3 it will be best to use the one that has measurements that most closely resemble what is already on your trailer. For example, if…

view full answer...

Answer 9

For double eye leaf springs, I recommend going with the 4-Leaf Double-Eye Spring #SP210275. This spring is 25-1/8 inches long x 1-3/4 inches wide and designed for 3,500 pound axles. These springs are a common length for 3,500 pound trailers. One…

view full answer...

Answer 10

Bushings do not always have to be used. Springs typically have bushings or they will use wet bolts depending on which part of the suspension system it is but not always. The bushings limit the wear on the suspension components. There are just…

view full answer...

Answer 11

The Brophy D-Ring Tie Down Anchor #DR01 features a 5/8 x 3 inch coarse thread bolt. It is designed for use with the Backing Plate #BP1D so it is not available with a different bolt thread. I have attached a couple short video reviews on this product…

view full answer...

Answer 12

I recommend using 1/4" or 1/2" D-rings with the Bulldog Winch Ratcheting Wheel Tie-Down Strap for Oversize Spare Tire - Horizontal Mount - 2,000 lbs #BDW20363. You can use the Brophy Swiveling D-Ring Anchor w Backing Plate and Hardware -…

view full answer...

What Is The Distance Between The Mounting Holes On The Buyers Products 5/8" D-Ring 337B40MP?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching