Size of Nut For Erickson Flag Pole Holder EM85HR

Question

Question:

What is the size and thread of the bolt and nuts that are used on the J clamp?

asked by: Michael K

0

Expert Reply:

I reached out to Erickson, who said the nuts on the Erickson Flag Pole Holder # EM85HR were 10 mm but they did not have the threading.

I have added a link below to a video review for you to check out as well of the Erickson Flag Pole Holder # EM85HR.

expert reply by: Kyle S

0

Answer 1

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 4

Hey Mark, from previous customers we have determined that the your 2009 Coachmen Chapparal M-278 has a Lippert 1621 pin box so the Gen-Y Gooseneck adapter part #GY58GR would fit and work great on it. This will give you a cushioned gooseneck adapter.…

view full answer...

Answer 5

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 6

The Patriot Slider part #BWRVK3270 might be a bit more noisy than the Companion slider part #BWRVK3400 due to the increased number of mounting points, 4 at the corners vs. 1 in the center. Probably not that noticeable and certainly not something…

view full answer...

Answer 7

As long as the RBW Lil' Rocker mounts to industry standard base rails you'll need the Curt Adapter Rails #C29BR that fit in the OEM puck system on your 2019 Ram 2500 and give you a standard base rail connection. I'm attaching a photo…

view full answer...

Answer 8

Hey Robert! Yes, the Roadmaster Comfort Ride Leaf Spring Suspension Kit w/ Shock Absorbers #RM-2460-2570 can be used to replace the MORryde LRE suspension kit you currently have on your 2006 Keystone Montana. Just verify your axles have a 3"…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

The factory prep package or pucks are not the same between Ram, GM and Ford. The spacing is all different which means you cannot use a 5th wheel hitch for Ram pucks on a GM with pucks. Take the Curt A25 5th Wheel Trailer Hitch for example which is…

view full answer...

Answer 12

Because your trailer has a Turning Point pin box and your Ram has a 6.5' bed I do recommend going with a fixed hitch and using the Turning Point as a rotating pin box to give yourself enough turning clearance. With you also having a puck system…

view full answer...