Where to Find Brake Controller Install Plug on 2009 Ford F-150

Question

Question:

Cant locate where to plug in the trailer brake control module. OEM Trailer Brake connection on 20099 Ford f150?

asked by: Ben

0

Expert Reply:

I attached a picture of the panel that would need to get removed on your 2009 Ford F-150 to access the brake controller harness. The correct harness to use with the controller # TK90160 that you referenced is the # 22292 for your truck.

expert reply by: Jameson C

0

Panel removal for brake controller harness
(click to enlarge)

Answer 1

They will, but you'll need to install a brake controller to actuate the trailer brakes. I'd recommend a reasonably priced proportional controller like the Brake EVN #TK63VR. For safe, predictable trailer braking a proportional controller is…

view full answer...

Answer 2

Yes. You can install the Curt T-Connector #C56413 on your 2019 Ford F-150 and it will be compatible with your factory brake controller. This will install a fully functioning 7 way connector on your truck to allow you to tow a trailer with brakes.…

view full answer...

Answer 3

Where exactly are you attempting to plug the harness in? Unlike many trailer connectors, the #C56413 doesn't use a round connector. The connector you're looking for is located on the cross-member directly behind the 7-way, it could be…

view full answer...

Answer 4

All the 2020 Ford F-150 trucks have the ability to upgrade to a 7 Way. The picture you supplied does look to be the port the Curt #C56413 will connect to. I included an install video we did on a 2019 F-150, but the install will be the same on your…

view full answer...

Answer 5

For your 2017 Ford F-150 we have the 7-way kit part #C56413 as a confirmed fit. This plugs into the trailer wiring connector that is present at the truck frame rail and gives you a functional 7-way. I attached an install video for this for you to…

view full answer...

Answer 6

According to the owners manual for a 2014 Ford F-150, Fuse 17 is a 30 amp fuse for the brake controller. If there is no fuse in that location then the brake controller isn't going to work. I recommend adding a 30 am fuse and testing the Tekonsha…

view full answer...

Answer 7

Though your 2018 Ford F-150 does have a plug under the dash, not all the wires are connected and you will need extra wiring to get it working, This can be quite the pain to do, so it is actually easier to just run all new wire for the 7 Way. If you…

view full answer...

Answer 8

The correct 7-way kit for your 2018 Ford F-150 that matches the rectangular connectors you sent us a picture of is the Curt part #C56413. I attached a picture our installers took that shows this connecting to same connectors.

view full answer...

Answer 9

To install a 7-way on a 2018 Ford F-150, you'd use the Curt #C56413 which installs as shown in the linked video.

view full answer...

Answer 10

You are correct, the Tekonsha Plug-In Adapter #22292 is what you need to install your Tekonsha Prodigy P3 #90195 in your 2015 Ford F-150. In your 2015 F-150, the plug in for your adapter may be under your dash near the top of your brake pedal. The…

view full answer...

Answer 11

Your 2018 Ford F-150 without the tow package and 7-way does have brake controller wiring currently so once you have the 7-way part #C56413 installed you'd be able to easily install a brake controller using the truck's factory wiring. The P3…

view full answer...

Answer 12

Yes, brake controller wiring harness #22292 and 3036-P are the same wiring harness. No matter which number it has on it the harness will fit the following vehicles: 2009 - 2016 Ford F-150 with factory 4-Flat or 7-Way 2012 - 2016 Ford Flex with…

view full answer...

Where to Find Brake Controller Install Plug on 2009 Ford F-150

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching