Lug Nut Torque for Higher Capacity Trailer Axles

Question

Question:

What I’d the lug nut torque on a load master 12000 pound alxle

asked by: Dale V

1

Helpful Expert Reply:

For 9/16 inch lug nuts torque them to 135 - 145 foot pounds.

And for 5/8 inch lug nuts torque them to 175 - 225 foot pounds.

I'd imagine a 12k rated axle has the 5/8 inch stud diameter but you should verify.

expert reply by: Jameson C

1

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The lug nut torque will depend of the diameter of your wheel studs and the construction of your wheels. • For a steel wheel and a 1/2 inch stud, torque the lug nut to 90-120 foot lbs • For a steel wheel and a 9/16 inch stud, torque to 120-140 foot…

view full answer...

Answer 3

I apologize for any confusion on what the proper torque specs are for 1/2 inch lug nuts on trailer wheels. I attached a picture of a chart to the right that details what the proper torque specs are for a trailer wheels lugs based on lug size, wheel…

view full answer...

Answer 4

When our installers replace a trailer hub, there isn't a set torque spec used when tightening the spindle nut. The hub is placed on the spindle, making sure the inner and outer bearings are correctly seated. The spindle nut is then run down until…

view full answer...

Answer 5

That really depends on the material of your rim and the diameter of your wheel studs. If you have a steel wheel with a 1/2 inch stud you would use 90-120 ft/lbs. Steel with 9/16 inch stud 120-140 ft/lbs. Aluminum with 1/2 inch stud 90-100 ft/lbs.…

view full answer...

Answer 6

It looks like you recently purchased some Kodiak Wheel Bolts #K58WB316 and 5/8" flange nuts #95188 from us, so thank you for being a loyal customer! What you'll want to torque those to will depend on the construction of your wheels and the…

view full answer...

Answer 7

The appropriate torque spec for any application will vary depending on the construction of the wheel as well as on the stud size. I suggest checking the wheels you're using to see if their manufacturer has a suggested torque rating. Steel trailer…

view full answer...

Answer 8

The MB Sturgis RV Quick-Connect Propane Grill Hose, #100304-120-MBS, will connect to a quick connect on a RV's LP system and the end can be connected to the regulator on the grill. The grill end connector is a 3/8 female flare swivel and the hose…

view full answer...

Answer 9

Your quick disconnect was designed for appliances like a grill or stove to be used. Certain grills do have a different connection that requires more power as your Coleman Roadtrip may. Based on some research there are many videos that show how to…

view full answer...

Answer 10

The propane regulators typically use a 3/8" female flare fitting for the accessory side. Therefore, if you are left with a 3/8" male flare fitting once the regulator is removed then you can use the MB Sturgis RV Quick-Connect Propane Grill…

view full answer...

Answer 11

You can add larger wheels and tires to a trailer as long as you have enough room for the larger size. The main clearance issues we find when putting larger tires and wheels on a trailer is from the top of the tire to the fender and from the inside…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Lug Nut Torque for Higher Capacity Trailer Axles

Product Page this Question was Asked From

Continue Researching