Solution for Older Atwood Surge Actuator with Bad Shock

Question

Question:

I have an Atwood surge brake actuator that I need a new shock absorber for. It is an older model, possibly in the 1980s. I cannot find a model number on it anywhere. The shock absorber is six and three-quarter inch eye to eye closed and 9 and 1/2 inch fully opened. It is secured by 7/16inch bolts each end. Can can you help me find this part?

asked by: Wayne L

0

Expert Reply:

Atwood is no longer making actuators at this time so there are no replacement shocks for their actuators anymore. Especially for ones as old as yours. So what you'd need to do is replace the surge actuator with a similar A-frame actuator like the part # DM8609502 which fits a 2 inch ball and is designed for drum brakes. There isn't a similar shock available we can recommend either.

expert reply by: Jameson C

0

Answer 1

The best recommendation I can give you since we don't carry the Gabriel actuators would be to check out the link I attached that will take you to a page that has all of the actuator shocks we carry. On the product pages for each there will…

view full answer...

Answer 2

The Surge actuator you currently have installed is an older Atwood model. The cap for the brake fluid confirmed that for me once I saw it. Problem there is that Atwood is no longer in business and no replacements are available, unfortunately. We do…

view full answer...

Answer 3

I do have an option for you but the coupler on your trailer is very old and we simply don't carry parts for them anymore as they were discontinued by the manufacturer. Therefore, the only option we can offer is a new coupler, the Demco…

view full answer...

Answer 4

To replace the Atwood 82541 surge brake actuator on your 1985 Trail-Rite boat trailer with drum brakes I recommend the Titan Zinc-Plated Brake Actuator - Drum - Multi-Fit Ball - Bolt On - 7,000 lbs #T43397007K which will fit your 3" wide…

view full answer...

Answer 5

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 6

I do have an option for you but Atwood has went out of business some years ago so there are no longer any replacement parts available for their trailer couplers. Therefore, the only option you have would be to replace the entire trailer coupler but…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 9

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 10

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...