Could Bauer Products T-Handle BA47VR Fit 2003 Glasstite Camper Shell

Question

Question:

I have a 2003 glasstite 8 ft long fiberglass dark garnett shell with #.s 382319 stamped, and the right side lock on the handle wont turn and I was wondering if BA47VR would fit

asked by: TOM S

0

Expert Reply:

The Bauer Products T-Handle Lock for Truck Caps # BA47VR is designed to fit standard truck caps like what you have so this would work well for you.

expert reply by: Jameson C

0

Answer 1

Yes, we do have locking t-handles. I recommend the Bauer Products T-Handle Lock for Truck Caps item #BA47VR. This t-handle is 3-1/2" long x 2" wide, the length of shaft is 2", and the distance between mounting holes center to center is…

view full answer...

Answer 2

The difference between the Pop & Lock #PAL9555 and #PAL9772 is that the #PAL9555 kit comes with a powered handle that will replace the existing rotary handle. The #PAL9772 conversion kit will turn the existing handle on the truck cap into a…

view full answer...

Answer 3

The Bauer Products T-Handle Lock for Small Truck Caps part #BA97VR comes with a K-127 key so if you order multiple they will all use this same key code.

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 5

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 6

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 7

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 8

Since the discontinued MaxxAir 4700k model fits a standard 14 x 14 RV vent opening, I recommend the MaxxFan Plus Roof Vent w/ 12V Fan - 10 Speed #MA00-04500K. The MaxxFan Plus comes with a thermostat and a remote for easy temperature customization.…

view full answer...

Answer 9

I'm assuming your Express doesn't have the 7-way, but does have the capped round plug behind the bumper on the drivers side frame rail, you'll install part #30955. Simply remove the cap and plug the connector in. To wire up the controller…

view full answer...

Answer 10

For a standard replacement equalizer for your Dexter 13-122 equalizers you'd want the #TREQE1 or for a cushioned version you'd want the part #K71-653-00 which comes with new shackles and bolts. For a kit that includes new bolts, bushings, and…

view full answer...

Answer 11

The correct Roadmaster base plates for your 2007 Toyota Tacoma are the following: - Direct-Connect #1175-3 - Crossbar-Style #1175-1 If your Roadmaster tow bar has individual joints with bolts, like what we see pictured with the Falcon All-Terrain Tow…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Could Bauer Products T-Handle BA47VR Fit 2003 Glasstite Camper Shell

Product Page this Question was Asked From

Continue Researching