Replacement Bearing Kit for Lippert 3500lb Axle

Question

Question:

Looking for a replacement bearing kit with seals for a lippert 3500 lb axle Nv 145911.

asked by: Andy

0

Expert Reply:

The Bearing Kit # BK2-100 is the correct kit for your Lippert 3500lb axle. This will include the inner and outer races and bearings with a new grease seal, cotter pin and tang washer.

I recommend using a Bearing Packer # PTW1218 with LubriMatic LMX Industrial Strength Grease # L11390 for the new bearings. This will ensure that you get grease throughout the bearing before installation.

expert reply by: Bud M

0

Answer 1

The standard 3,500 lb axle uses the Hub Bearing Kit #BK2-100 which is for a #84 spindle. If your axle is a 1990 or newer then you likely need these parts but if it's older then I'll need you to measure your spindle to make sure we can get you…

view full answer...

Answer 2

Yes, the Bearing Kit #BK2-100 are top quality for long life.

view full answer...

Answer 3

The correct bearing kit for your Lippert 3,500 lb axle is the Bearing Kit #BK2-100. This kit uses inner bearing #L68149, outer bearing #L44649, their accompanying races, along with grease seal #58846. I've added a link to a video review of this…

view full answer...

Answer 4

The correct replacement bearing and seal kit for your 3,500 lb Dexter Axle is the Hub Bearing Kit #BK2-100 for the #84 spindle. This kit comes with inner bearing #L68149, outer bearing #L44649, and a grease seal with a 1.719" ID and 2.565"…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 10

It does appear you are going to be able to flip the axles on your 2023 Northern Spirit 2145RBX using 2 of the Dexter Trailer Springs Over-Under Conversion Kits #K71-384-00. I will warn you Kalvin this will raise the height of your camper roughly…

view full answer...

Answer 11

You can verify that the 10-19 grease seal included in Bearing Kit #BK2-100 is the correct one for your spindles by taking two measurements. First you want to measure the rear hub bore where the seal is inserted. The seal's outer diameter needs to…

view full answer...

Answer 12

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Replacement Bearing Kit for Lippert 3500lb Axle

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching