Replacement For MaxxFan 10-4301K Circuit Board

Question

Question:

Maxxair vent 12 volt 4 speed fan. have no model # and motor is OK, does the MA10-04301K-V16 replace my old board? Im not sure! my old board is a 10-4301K.

asked by: Ronald J

0

Expert Reply:

You are on the money with the replacement circuit board you need for your MaxxAir 10-4301K, which is the following:

- Replacement Printed Circuit Board and Switch for MaxxFan Roof Vents # MA10-04301k-v16

I have added a link below to a video review for you to check out as well if you'd like to take a look.

expert reply by: Kyle S

0

Answer 1

In order to replace the circuit board on a MaxxFan Deluxe 5100K #MA00-05100K you'll want to use part #MA10A21276K

view full answer...

Answer 2

If you measure just the width of your toy hauler's rear door opening I can determine which LaSalle Bristol CrossBreeze Screen you'd need. The part #3441409775PBK that you referenced is the correct screen if your opening is 97-3/4…

view full answer...

Answer 3

Your MaxxFan Plus Roof Vent w/ 12V Fan and Thermostat - Manual Lift - 10 Speed - White #MA00-04000K could be cutting off after 10 seconds for the following reasons: 1. Insufficient or fluctuating power. Your fan could be receiving less than 12v of…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 10

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 11

Hey Travis, congrats on the new 2024 Jayco Flight 284BHS! Your travel trailer looks to have a GVWR of 7,950 lbs so I recommend going with the Equal-i-zer Weight Distribution w/ 4-Point Sway Control #EQ37121ET and pairing it with the Shank…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Replacement For MaxxFan 10-4301K Circuit Board

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching