Does Bumper have to be Removed to Install Front Mount Trailer Hitch on 2006 Jeep Wrangler Unlimited

Question

Question:

Will I need to take my factory front bumper off to put you product on?

asked by: Phillip

0

Expert Reply:

If your 2006 Jeep Wrangler Unlimited has a C-channel bumper and not a tube style bumper then front mount trailer hitch # 31408 will fit. To install this hitch you will not need to remove the vehicle bumper. There is a plastic shield between the bumper and grille that will have to come off but it does get reinstalled. I have included a link to the installation instructions for you to view. Basically, the hitch attaches to the top of the C-channel bumper.

expert reply by: Michael H

0

Answer 1

I went out the warehouse and took the measurements you asked about on the Curt Front Mount Hitch, part #31408. I've attached a diagram showing them. The inside distance between the mounting plates is about 27-1/2 inches. Between the 2 sets of…

view full answer...

Answer 2

The loops that are attached to the Curt Front Mount Trailer Hitch Receiver part #31408 can be used for vehicle recovery according to my contact at Curt. However, if you will be pulling anything toward the 9,000 lb line pull capacity of the hitch then…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 7

I definitely understand being a bit overwhelmed by the amount of options in front of you, however I can definitely help with differentiating the trailer hitches for your 2019 Subaru Outback Wagon along with explaining my personal recommendation,…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

The Kuat Sherpa 2.0 #SH22G and the NV 2.0 #NV22G that you referenced are both excellent platform-style racks that will hold your bikes by the front wheels with no frame contact. These are top-of-the-line carriers and you really would not go wrong…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Does Bumper have to be Removed to Install Front Mount Trailer Hitch on 2006 Jeep Wrangler Unlimited

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching