Bumper Replacement for a 1995 Ford F-350

Question

Question:

Looking for a deep or cowboy bumper for my 1995 f350. Any help? Thanks

asked by: Nathaniel R

0

Expert Reply:

I may have a few options for you but unfortunately we do not have any of the real deep/cowboy style bumpers. We have the Westin Fey Surestep # 21007-92230 or the Westin Fey Diamondstep # 21000-92230 if you were wanting to go with a more rugged or traditional look.

expert reply by: Jacob H

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 6

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

As far as wiring for the 2024 Toyota Grand Highlander, we do have the Curt #C59236 available which is more of a universal hardwire harness. Unfortunately there are not any plug-and-play options that have been confirmed to fit as of yet (October 4,…

view full answer...

Answer 10

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Answer 11

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 12

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...