Can the Erickson Big Bed Load Extender Be Used As a Roof Extender

Question

Question:

can the erickson big bed load extender be converted to a single bar roof rack like the darby extend a truck? Thanks.

asked by: Doug H

0

Expert Reply:

The Erickson Big Bed Load Extender part # EM07600 is a bed extender only. That said, we have plenty of options which are both a bed extender and roof extender like the Erickson Big Bed Junior part # EM07605 or the Malone Axis Truck Bed and Roof Load Extender part # MPG907.

expert reply by: Conner L

0

Answer 1

There is no reason why you couldn't install a front mount hitch and and add a front load bar to help support your Kayak and create more clearance between it and your travel trailer. The front mount hitch I recommend for your 2007 Toyota Sequoia…

view full answer...

Answer 2

The Curt #C57WR truck bed extender isn't a vehicle-specific item, so Curt doesn't test fits on specific vehicles. If the inside of the tailgate opening (jamb to jamb) is 60-1/2 inches, the bed extender would fit. However, this extender is…

view full answer...

Answer 3

I do have an option for you for more support but we don't have any three crossbar setups for a 2012 Honda Pilot. Instead, you will need to add a hitch mounted load support like the Malone Axis Truck Bed and Roof Load Extender for 2" Hitches…

view full answer...

Answer 4

All roof racks currently made for your 2018 Hyundai Ioniq, shown on the linked page, consist of two crossbars and the related foot assemblies. But since you have a hitch support like the Malone Axis #MPG907 to hold one end of your canoe I do have a…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The best hitch for a 2024 Subaru Outback is the etrailer item #e25TR. This hitch is custom fit and bolts to your Subaru with included hardware. This is a class III hitch with a 2" receiver, that has a 3,500 lbs towing capacity and a 350 lbs…

view full answer...

Answer 7

The total height from the bottom of the receiver tube to the top of the closed GearLocker on the Yakima Exo Swing Away Storage System #Y74ZR is 42-1/2 inches tall. I went ahead and attached a diagram that shows this height for your convenience.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

That is a keen observation and a good question. I actually had the chance to assist with assembly of one of the Flint Hill Goods 30" x 50" Wheelchair Carriers #FHG99ZR not too long ago. The main bolt for the shank is indeed quite large, so…

view full answer...

Answer 10

The Curt Cargo Carrier #C18113 will definitely work with the etrailer #e25TR on your 2024 Outback. Keep in mind, you will be limited to the 350 lb max tongue weight of the hitch or the max tongue weight of your vehicle. Whichever is lower is what you…

view full answer...

Answer 11

Hello Craig. I do have a solution for you, but the Flint Hill Goods Wheelchair Carrier #FHG99ZR is not recommended for use behind RVs, campers, or trailers. The ride on the back of a 5th wheel or RV is a lot more rough than on the back of a car or…

view full answer...

Answer 12

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Can the Erickson Big Bed Load Extender Be Used As a Roof Extender

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching