Location Of Switch For Lithium Setting On Progressive Dynamics RV Power Control Center PD4135K

Question

Question:

I just picked up the converter and am looking for the lithium battery switch?

asked by: Lawrence L

0

Expert Reply:

Thank you for the business!

The switch to change the Progressive Dynamics RV Power Control Center with AC/DC Panel and Converter/Smart Charger - 35 Amp # PD4135K to the lithium-ion setting will require you to remove the front panel and is located underneath the fan as you can see in the included picture.

If you take a look at the 2:20 minute mark of the included video it will show you the location of the switch as well.

expert reply by: Samuel C

0

Lithium Switch
(click to enlarge)

Answer 1

We do actually have Dexter electric drum brakes in your required 10 x 1-1/2-inch size, parts #K23-473-00 and #K23-472-00, which are right- and left-hand, respectively. These are complete bolt-on (4-bolt) replacements that fit wheels diameters from…

view full answer...

Answer 2

It should be getting close to 12 volts if the power output is set to the maximum on the brake controller. Some brake controllers will not work properly if they are titled or turned to the side or if it has a leveler knob that is not level. Check…

view full answer...

Answer 3

On a 12 inch brake assembly magnet, you should be getting 3.2 to 4 max amps at 12 to 13 volts. We have an FAQ article that covers testing brakes and brake magnets that should be helpful to you. I have included a link to it. Replacing the magnet is…

view full answer...

Answer 4

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Answer 5

90-120 ft lbs of torque is probably about right for your 15 inch trailer rims. If you check out the lug nut torque chart that I attached you will see that nearly all of the torque specs are that and higher. You'll need to know the diameter of the…

view full answer...

Answer 6

I apologize for any confusion on what the proper torque specs are for 1/2 inch lug nuts on trailer wheels. I attached a picture of a chart to the right that details what the proper torque specs are for a trailer wheels lugs based on lug size, wheel…

view full answer...

Answer 7

The Lippert Components Slide-Out Switch Assembly - White #LC117461 or black #LC117460 will work well for you. I've attached the wiring color coding in a photo to assist in your rewiring.

view full answer...

Answer 8

Is it possible there's grease in the drum which is causing the brakes to not lock up? If you blew out the inner grease seal or it was leaking at all this is a very likely cause. Otherwise it could be a mechanical problem of the assemblies and…

view full answer...

Answer 9

If the brake controller appears to working properly and the brakes of your electric over hydraulic setup are still not applying that would lead me to believe that the problem is on the actuator itself. Does the actuator cycle on to build pressure…

view full answer...

Answer 10

Using a weight distribution hitch with your Volvo XC90 would be strongly discouraged. Weight distribution hitches redistribute some of the load from the rear axle of the tow vehicle to the front axle, that force has to be transferred either through…

view full answer...

Answer 11

The RBW Little Rocker 5th wheel hitch is designed to mount to industry standard rails. The B&W Custom Base Rails, #BWRVK2602, are above the bed 5th wheel industry standard rails. The RBW hitch will work well with these base rails on your 2017 Ram…

view full answer...

Answer 12

I went to our warehouse and measured the holes you mentioned you wanted the measurement for on the Lippert 1621 5th Wheel Pin Box, part #LC1387882. The holes measure 3/8 inch diameter. I have also attached a drawing of this pin box with the…

view full answer...