Which Torklift StableLoad Fits 2020 Ram 3500 Dually and Does Not Require Drilling

Question

Question:

does the ram 3500 dually require drilling ? an does this fit TLA7311this truck

asked by: Craig C

0

Expert Reply:

The correct Torklift StableLoad fit for your 2019 Ram 3500 dually is the part # TLA7310S and does not require drilling.

expert reply by: Jameson C

0

Answer 1

I had the #TLA7310S pulled from stock, and found that the thickness of the spacers that sit between the lower overload spring and the bottom of the spring pack is 7/8 of an inch which is the same for the fronts and rears. I've linked to an…

view full answer...

Answer 2

I contacted Roadmaster to verify that the Rear Anti-Sway Bar, #RM73FR is a confirmed fit for the 2019 Ram 3500 be it DRW or SWR. They confirmed this part is the correct for either type.

view full answer...

Answer 3

I took a look at the installation of both parts, and from what I can see, a Titan's Midship & Stars fuel tank on your 2021 Ram 3500 will interfere with the Roadmaster Rear Anti-Sway Bar #RM73FR. A better option instead would be a kit from…

view full answer...

Answer 4

The Roadmaster sway bar part #RM-1129-144 is definitely a legit part number and the correct fit for your 2019 Ram 3500 dually. I attached a picture that I took from a set of install instructions I got off of their site that includes this part number…

view full answer...

Answer 5

We measured the TorkLift StableLoad #TLA7310S and found that from the center of the mounting hole to the furthest edge is 3-5/8 inches on one side, and 2-1/8 inches on the other side. To determine if the StableLoad will clear your Quadrasteer…

view full answer...

Answer 6

If you are getting a lot of squat when towing with your 2020 Ram 3500, the Firestone Ride-Rite Extreme Duty #F2710 will definitely be a good option. This is rated to 7,500 pounds when at full psi and will get the back end of your truck back to…

view full answer...

Answer 7

For your 2020 GMC Sierra 3500 4x4, I recommend using the Firestone Ride-Rite Red Label Extreme Duty Air Helper Springs part #F2710 over the Air Lift LoadLifter 7500 XL Air Helper Springs part #AL57541. The main reason is in regards to the…

view full answer...

Answer 8

I have a solution for you, but the Firestone Ride-Rite #F2709 you referenced are designed for Chevy HD trucks and not Ram trucks. However, you can use the #F2710, which are confirmed to fit your 2015 Ram 3500 Mega Cab and can be used with the B&W…

view full answer...

Answer 9

Most roof vents follow the standard size opening. That size is 14-1/4 inches by 14x1/4 inches but it is most commonly referred to as 14 x14. Many different vents on the inside and outside flanges can have different measurements to gain a certain look…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...