Will the Dexter E-Z Flex Suspension Kit Fit a Lippert 6K Axle

Question

Question:

Flex suspension kit K71-652-00 fit a 6000 pound Lippert axle

asked by: Doug M

0

Expert Reply:

Yes, the Dexter E-Z Flex Suspension Kit part # K71-652-00 will work on a Lippert 6K trailer axle. That said, you do need to confirm the spread is 33" (center to center) first.

expert reply by: Conner L

0

Answer 1

You're not going to have any problems mixing Dexter and Lippert components on trailer axles over 10k-lbs in the same manner as below 10k-lbs as long as the measurements on the replacement parts are the same- i.e. bearing sizes are the same,…

view full answer...

Answer 2

Nev-R-Adjust is Dexter's specific trade name for self-adjusting brakes like #23-458 and #AKEBRK-7L-SA. Self-adjust and Nev-R-Adjust are the same type of brakes. After their initial adjustment both will automatically maintain correct braking…

view full answer...

Answer 3

The attachment bolts for a 5-bolt brake assembly like the part #AKEBRK-6R should be torqued to 30-50 foot/lbs. If you don't have a torque wrench handy, if you tighten the bolts until the lock washers flatten out, you'll be pretty darn close…

view full answer...

Answer 4

Starting with the brakes if the pads on the shoes are cracked or if the wear indicators are showing then they should be replaced. If there are no wear indicators and you notice weak braking with the brakes adjusted out then they would need to be…

view full answer...

Answer 5

To initially tighten a Dexter Nev-R-Adjust Electric Trailer Brake Assembly, like part #23-468, you need to spin the wheel downwards (when looking at it from the backside) with a brake adjustment spoon #W80630 or flat screwdriver. If you are needing…

view full answer...

Answer 6

I'd recommend the Morryde cushioned equalizers over the EZ Flex since they have vertical cushioning whereas the EZ Flex cushions horizontally so the ride quality isn't as improved as much. So I'd go with the part #MR87ZR for sure over the…

view full answer...

Answer 7

You definitely can replace the MORryde suspension system on your 2011 Carriage trailer with the Dexter E-Z Flex Suspension System, like part #K71-652-00, as they both install on a hanger like the part #28-5. From what I can tell it looks like the…

view full answer...

Answer 8

Typically the way to fix grease fitting that won't take grease is to have them removed and cleared so that the obstruction is removed and it will function. What you will want to do is remove the zerk fittings of your equalizers with a wrench and…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 11

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Will the Dexter E-Z Flex Suspension Kit Fit a Lippert 6K Axle

Product Page this Question was Asked From

Continue Researching