How to Turn Off a Tekonsha PRIMUS IQ Electronic Brake Controller When Not Being Used

Question

Question:

I just bought a f350 , that has the primus brake system...I dont need it so how do I turn itoff

asked by: Diane

0

Expert Reply:

Electronic brake controllers like the Tekonsha PRIMUS IQ Electronic Brake Controller, part # TK90160, receive their power through the wiring harness that plugs into the rear of the unit. The other end of the wiring harness plugs into a connector under the dash board. If you do not intend to tow anything for the foreseeable future you can simply disconnect the wiring harness where it plugs into the vehicle wiring.

In the event that in the future you do want to use the brake controller for towing a trailer you will only need to reconnect the wiring harness to restores its power and its connection to the braking system in your F-350.

expert reply by: Adam R

0

Answer 1

The attachment bolts for a 5-bolt brake assembly like the part #AKEBRK-6R should be torqued to 30-50 foot/lbs. If you don't have a torque wrench handy, if you tighten the bolts until the lock washers flatten out, you'll be pretty darn…

view full answer...

Answer 2

My contact at Dexter Axle tells me that when installing a brake assembly to the backing plate of a 3500 lb axle, the bolts should be tightened in a criss-cross pattern to between 45-70 foot lbs.

view full answer...

Answer 3

On the Hopkins Graduated RV Levels, #HM08525, the level C is for front-to-rear level and can be installed on either side of the vehicle. The level 3 is for side-to-side level and can be installed on front or rear of the vehicle. Read both levels (C…

view full answer...

Answer 4

The Camco AccuLevel Trailer Bubble Level #CAM25563 is measured in degrees so that it will be compatible with multiple trailer sizes.

view full answer...

Answer 5

The numbers on the Hopkins Graduated RV Levels #HM08525 are just reference numbers and are not meant to indicate degrees or inches or feet. Basically it is a simple way to make sure the trailer is level on both sides. So if you are at 0 on one side…

view full answer...

Answer 6

The largest stick on level we offer for RVs is the Hopkins Never Fade Trailer Bubble Level Set #HM08526 which measures 3-3/4" long X 1-1/2" wide. The reflective bubble in the level make it easy to see from a longer distance like…

view full answer...

Answer 7

While we do have the stick-on graduated levels, each of them are in the 3 to 4 inch range like you mentioned and there aren't any that are larger. So the trade off of getting something like the 10 inch Camco AccuLevel Trailer Bubble Level…

view full answer...

Answer 8

It sounds as if you have a Tekonsha Primus brake controller without the boost function built in. Your controller should have a power adjustment wheel on the left side and a manual brake activation slide switch on the right side. If there is a lever…

view full answer...

Answer 9

There is a panel just under and behind your driver's side wheel well that you can remove to determine if you have the tow package or not. If you check out the attached picture you can see what wiring will be in this location for the tow…

view full answer...

Answer 10

A brake controller will be needed to actuate your electric trailer brakes. I can highly recommend the Tekonsha Prodigy P2, part #90885. The P2 is very easy to use and will provide safe and predictable braking for your trailer. The controller will…

view full answer...

Answer 11

Draw-Tite, Prodigy and Tekonsha brake controller all share the same style of connector. If thats what you have installed in your 2004 Dodge Ram 1500 then you would be able to swap in the Draw-Tite Activator IV Trailer Brake Controller #5504. If you…

view full answer...

Answer 12

For a trailer weighing 1200kg (2640 pounds) you would most likely only need boost setting 1 if at all when using the P3, #90195. But before setting the boost you will need to set the gain properly on the P3. To do this, follow these steps: First…

view full answer...