Can a Ram 1200 Single Speed Jack Be Upgraded To a Two Speed

Question

Question:

Can I convert my single speed weld on Ram Trailer Jack Model 12000 Series double landing gear to a 2 speed configuration? If so, do you sell the parts for that conversion?

asked by: Brandon B

0

Expert Reply:

I am not aware of any way to convert a single speed jack to a two speed jack. Therefore, you will need to replace the single speed jack with a two speed if you want this operation, the Square 2-Speed Jack with Crank part # TJD2SP-12000SP-F for 25-7/8" lift or part # e34FR for 25-1/2" lift.

expert reply by: Conner L

0

Answer 1

You are correct in that the follow leg does not need to change to convert your Ram jacks to a 2 speed setup. You'll need to replace the lead leg with the part #TJD2SP-12000SP-F which has a two speed input but the output shaft still spins same…

view full answer...

Answer 2

We do not have this item in stock for me to measure its thread pitch but two of us estimated it as being 6 or 7 threads per inch. I linked a photo of the instructions to replace this part. The bearing is removable and is available as a replacement…

view full answer...

Answer 3

We do in fact have the replacement gearbox you need for the 10,000 lb Square 2-Speed Jack #TJD2SP-12000SP-F. The part you need is the Replacement Gearbox for etrailer and Ram 2-Speed Square Jacks #TJD2SP-12900-GBX.

view full answer...

Answer 4

It is not possible for me to tell you with any degree of certainty that you can retrofit the Replacement Gearbox for etrailer and Ram 2-Speed Square Jacks #TJD2SP-12900-GBX for use with a single speed Ram jack though there are replacement gears…

view full answer...

Answer 5

For a wire loom for 7-way wiring we recommend 1/2 inch diameter like part #459075-1 that is sold by the foot. I have a 7-way adapter on my desk that has a wire loom on it that is 1/2 inch so I know this size would be correct.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

I definitely understand being a bit overwhelmed by the amount of options in front of you, however I can definitely help with differentiating the trailer hitches for your 2019 Subaru Outback Wagon along with explaining my personal recommendation,…

view full answer...

Can a Ram 1200 Single Speed Jack Be Upgraded To a Two Speed

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching