How do the Ultra-Fab Stabilizer Jack Attach to RVs

Question

Question:

We have a 2012 22GQ Arctic Fox trailer. I would like to know how this mounts to the trailer frame, bolted or welded? Another questions, what is the difference between the UF39-941704 and UF39-941705? Both are listed and 30inch extension and 6000lbs lift.

asked by: Glen J

0

Expert Reply:

The Ultra-Fab Power Twin II Manual Stabilizer for Trailers and RVs # UF39-941704 that you referenced is designed to be bolted on with the included mounting hardware.

The difference between the # UF39-941704 and the # UF39-941705 is that the # UF39-941705 comes with dual 12 volt motors to raise and lower the legs of the stabilizer jacks. Whereas, the # UF39-941704 that you referenced require manual operation that includes cranking a jack handle.

expert reply by: Jameson C

0

Answer 1

We can get your stabilizer set up, and I can tell you where each of the four wires go for the Ultra-Fab Power Twin II Electric Stabilizer with Dual Motors #UF39-941705. I have added a cut out for you of the installation instructions which cover how…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

By all accounts the Curt Spectrum Trailer Brake Controller #C51170 works well and is easy to use and install on most vehicles. It is a brand new item so not a lot of feedback has come in on it. I did learn a few things though after speaking with our…

view full answer...

Answer 5

I contact Ultra-fab and since the socket on the Ultra-Fab Power Twin II Manual Stabilizer for Trailers and RVs part #UF39-941704 is not a standard hex socket head there is not a way to raise and lower the stabilizer with a power drill. The socket on…

view full answer...

Answer 6

If you're talking about a space to sit between the mounting brackets of the Ultra-Fab Power Twin II Manual Stabilizer #UF39-941704 and the frame of the trailer then no, this stabilizer does not have spacers. If you're trying to gain more…

view full answer...

Answer 7

The mounting bracket for the Ultra-Fab Power Twin II Manual Stabilizer #UF39-941704 is approximately 35-3/8" in length. The frame height would dictate the amount of lift you would want but there are other factors to take into account. The…

view full answer...

Answer 8

The Ark Drop Down Corner RV Stabilizer Jacks #ARK94FR are able to lock into place at 30 and 60 degrees as stabilizers. They also have the 90 degree position where it is rated for 1,929 lbs and then the stored position.

view full answer...

Answer 9

The 30" Ark Drop Down Corner RV Stabilizer Jacks #ARK94FR have a weld on design. This is the only way to install the jacks with the included mounts as there is not enough room between the stabilizer itself and the mounting plate for additional…

view full answer...

Answer 10

The Ultra-Fab Power Twin II Manual Stabilizer #UF39-941704 that you referenced fits trailers that have frames that are 48 to 80 inches wide. Since you measured 67-1/8 inches wide this would easily fit your trailer.

view full answer...

Answer 11

Yes, the Ark Drop Down Corner RV Stabilizer Jacks #ARK94FR are definitely an upgrade over standard trailer stabilizers. The drop down feature makes it a lot quicker to get the jacks up and tucked out of the way so they don't catch when the…

view full answer...