What is the Mounitng Hole Center on Center on the ComeUp Cable Tensioner

Question

Question:

will part cu881087 work with a trail fx 8000.

asked by: John K

0

Expert Reply:

The ComeUp Cable Tensioner part # CU881087 has mounting holes that are 10" on center. This is a pretty common size but I would recommend checking your winch to see what the mounting holes are on it to make 100% sure it will bolt on.

expert reply by: Randy B

0

Answer 1

The Tensioner for Bulldog Winch Standard Series Truck Winch - Wire Rope #BDW20234 or the ComeUp Cable Tensioner for DV-12, DV-15, and DV-18 winches #CU881087 are the only options for that size a winch. We have not tested them on a Smittybilt x20…

view full answer...

Answer 2

See the attached photos. The first photo shows the mounting bolts, which are 10” apart, center to center. The second photo is the roller, which is 8” in width. The last photo shows the roller bracket, which is 7.25” in width.

view full answer...

Answer 3

The Tensioner for Bulldog Winch Standard Series Truck Winch #BDW20234 will help in evenly putting the cable on but you would still want to watch it and make sure it is spooling up the right way.

view full answer...

Answer 4

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Yes, the DeeMaxx Disc Brake Kit #DE66YR will allow you to use 14" trailer wheels.

view full answer...

Answer 11

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 12

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

What is the Mounitng Hole Center on Center on the ComeUp Cable Tensioner

Product Page this Question was Asked From

Continue Researching