Will 14" Diameter Trailer Wheels fit On The DeeMaxx Disc Brake Kit # DE66YR?

Question

Question:

Hi, will these fit a 14inch wheel? I assume so, but cant find any specs from the manufacturers website. Thanks

asked by: Steve

0

Expert Reply:

Yes, the DeeMaxx Disc Brake Kit # DE66YR will allow you to use 14" trailer wheels.

expert reply by: Bud M

0

Answer 1

Based on the information you sent, I recommend the Galvanized Trailer Idler Hub Assembly for E-Z Lube, Item #AKIHUB-545-35-G-EZ-K. This hub kit is great for marine use and includes the inner bearing (Item #L68149) and race, outer bearing (Item…

view full answer...

Answer 2

You can certainly go ahead and re use the existing 2 bolts, provided they are in good condition. The fish wire method shown in the video works too, but it is also very common to just use the two bolts like your old Atwood actuator. Personally I…

view full answer...

Answer 3

Two bolts will be sufficient for installing the Demco Hydraulic Brake Actuator #DM72VR. You will want to use two Requires 2-1/2" x 4-1/2" Grade-5 of Grade-8 bolts. Personally I would use something like the Curt Coupler Hardware Kit…

view full answer...

Answer 4

I'm going to provide you with the most common setup but it will require you to confirm your measurements on your trailer. You can use the article linked below as well as the picture below to see the measurement points that will need to be…

view full answer...

Answer 5

Yes, the Kodiak Disc Brake Kit item #K2HR35DS. Those are 10" Hub/Rotor with a 5 on 4-1/2 bolt pattern that will fit 14"-15" wheels. The hubs are corrosion resistant with a dacromet plating. They are sold in pairs so you will need to…

view full answer...

Answer 6

The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-20 is a direct replacement for your Tie Down model 70E disc brake actuator with a 7000 lb capacity (Tie Down was bought out by Dexter back in 2017). Although I don't have a way of decoding your…

view full answer...

Answer 7

I would first try bleeding the brakes to first make sure there's no air in the lines as that prevents them from working but also will give you an idea if the master cylinder is working as well. We do carry some replacement parts but I would need…

view full answer...

Answer 8

To replace the rotors of your disc brakes, the Kodiak #KR12D will work just fine as they are a standard 12-1/6" wide overall and have an inner diameter of 7-2/3" (where the hub sits). We don't have a dimensional drawing but as long as…

view full answer...

Answer 9

Trailer brake actuators like the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout #DX56FR you're looking at are rated more for the brake type and not necessarily a specific amount of axles since it has to do with the amount of pressure the…

view full answer...

Answer 10

Both races you mentioned are related to the same bearing, #L68149. The difference in the races is the outer diameter. The outer diameter is important for the hub that the race fits so because the hub bore in the rotors is different than the hubs you…

view full answer...

Answer 11

The holes in the DeeMaxx 10" Hub-and-Rotor Assembly #DE49VR are designed to avoid water pooling into that part of the assembly. I wouldn't say that pooling what is a massive issue, but just the fact that DeeMaxx built this in and is making a…

view full answer...

Answer 12

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Will 14" Diameter Trailer Wheels fit On The DeeMaxx Disc Brake Kit # DE66YR?

Product Page this Question was Asked From

Continue Researching