Tie Downs for 2003 Chevy Silverado 3500 Dually

Question

Question:

I have a 2003 chev Silverado crew cab dually and want to tie down a lance 1172. What mounts do I need for the truck?

asked by: Bill

0

Expert Reply:

For your 2003 Chevy Silverado Crew Cab dually the correct Torklift Tie downs you'd want are the tie downs part # TLC4203 and # TLC3206 and you'd be set.

Then for a set of turnbuckles to attach from from you camper to the tie downs the part # TLS9529-2-LK would be a great option as well.

expert reply by: Jameson C

0

Answer 1

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 2

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 3

The support braces in the HappiJac Truck-Mounted Camper Tie-Downs #LC182860 are going to attach to the cross frame to provide support for the anchors which will bolt through the bed wall and into the braces. The rear anchors will bolt through the…

view full answer...

Answer 4

I'm assuming your 2024 F-250 has the 6-3/4' bed. If that is correct, the right tie-downs are in fact the #TLF3008 and #TL77CR. TorkLift has accounted for the bed access steps on the 2024 model and confirmed these will fit your truck.

view full answer...

Answer 5

The primary advantage of frame-mounted camper tie-downs like the TorkLift #TLF2012A and #TLF3001A, which are designed to fit your Ford F-350 if it has the 6-3/4 foot bed without a step/board underneath and a factory hitch, is the stability they…

view full answer...

Answer 6

There is not a plug and play adapter for your Lance connector that we are aware of. Typically this is installed by the Lance dealer. A junction box/7-way plug kit like #HS381-9000 is an option you have to convert the camper to match the 7-way RV…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

You do not need to remove the bed of your truck to install the HappiJac part #LC182906-182971 that you referenced. I found a copy of the install instructions for this part number (see attached pictures) and there's no mention of the bed needing…

view full answer...

Answer 9

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 10

To install a brake controller like the #5504 that you referenced you only need to connect it to 4 wires. If you find more wires on your vehicle than would be needed to install the controller you wouldn't need to do anything with them. I attached…

view full answer...

Answer 11

Yes, it will! The Hellwig Adjustable Big Wig Rear Anti-Sway Bar item #HE96XR is confirmed to fit your 2024 Chevy Silverado 3500. This sway bar will minimize lateral movement in your rear end and improve stability. This sway bar is made in the USA and…

view full answer...

Answer 12

The 1-5/16" Hellwig Adjustable Big Wig Rear Anti-Sway Bars are designed for 2WD #HE97MR or 4WD #HE94FR versions of your 2021 Ford F-250. These are both designed for trucks which have a stock ride height. Hellwig does offer their 2" Lift…

view full answer...

Tie Downs for 2003 Chevy Silverado 3500 Dually

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching