Distance from Upper Weld Stop to Center of Torque Tube on Stromberg Carlson Landing Gear

Question

Question:

Hi, can you give me the vertical distance from the bottom of the upper weld stop to the centerline of the torque tube on this item. Thanks, and best regards

asked by: Hal B

0

Expert Reply:

I had the Stromberg Carlson Landing Gear # RVLG-8000 pulled from the warehouse and we measured 7-1/4" from the top of the upper weld stop to the center of the torque tube. I've also posted a diagram of these measurements.

expert reply by: Erik B

0

click to enlarge

Answer 1

We have not yet (as of April 2019) had a chance to install any wired trailer brake controllers on a 2019 Ford Ranger so for guidance I checked with my most trusted brake controller expert at Tekonsha. Based on what I could learn about the truck if…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 4

Good news! I was able to go out to the warehouse and measure the etrailer landing gear #RVLG-8HDL for you. I found that the distance between the weld stops from the outside to outside is 17-1/2 inches and from the inside to the inside of the weld…

view full answer...

Answer 5

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 6

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 7

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 8

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 9

Assuming your tires are in good shape without any bulges the easiest way to determine if you have a bent spindle is to take a straight edge that is longer than the tire and lay it across the tire parallel with your trailer frame and then measure the…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Answer 12

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...