Mounting Hole Spacing on the Buyers Products Black Receiver Tube

Question

Question:

Dear Etrailer: I’m trying to understand the center to hole spacing and I see conflicting information between the item diagram vs the qanda. Diagram says 3-3/8” vertical x 3-1/2 horiz and the qanda says 3-3/8” horiz x 3-1/2 vert. Which is correct. .

asked by: Greg S

1

Helpful Expert Reply:

Tha Buyers Products Black Receiver Tube part # 3371804055 has a vertical spacing of 3-3/8" center to center and horizontal spacing of 3-1/2" center to center spacing.

I have linked a photo showing these for you. We do confirm these measurements when we receive the products and strive to have the most accurate information available on our site.

expert reply by: Randy B

1

click to enlarge

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

I definitely understand being a bit overwhelmed by the amount of options in front of you, however I can definitely help with differentiating the trailer hitches for your 2019 Subaru Outback Wagon along with explaining my personal recommendation,…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The Kuat Sherpa 2.0 #SH22G and the NV 2.0 #NV22G that you referenced are both excellent platform-style racks that will hold your bikes by the front wheels with no frame contact. These are top-of-the-line carriers and you really would not go wrong…

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

I have a solution for you but the Buyers Products Hitch Plate for Pintle Mounting item #3371809030B only fits 1999 and newer Ford F-350's. For your 1986 F-350 Cab and Chassis you will want the Buyers Products Flatbed/Flatbed Dump Hitch Plate…

view full answer...

Answer 10

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 11

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 12

I think the best option we have for you is a universal weld-on hitch plate like one of the following that I have attached for you. We do not really have any direct fit hitch plates for you so I think this will be the best option we can offer. If you…

view full answer...

Mounting Hole Spacing on the Buyers Products Black Receiver Tube

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching