Replacement Parts for the Dutton-Lainson Sidewind Swivel Trailer Jack # DL22800

Question

Question:

we purchased a aluma trailer in late summer of 2009 and im in need of a new jack handle with two bushings is it possible that these items could be orderd?

asked by: Jim W

0

Expert Reply:

I do carry replacement parts for the Dutton-Lainson Sidewind Swivel Trailer Jack, part # DL22800 that you have referenced.

The replacement handle is the Dutton-Lainson Replacement Handle, part # DL22448 and the bushings for the handle you will need are in the Dutton-Lainson Replacement Miter Gear Kit, part # DL22439. See the included picture that will show the handle labeled X and the gear kit labeled A.

If you have a different brand or type of trailer jack let me know the make and model and I will be glad to help you with replacement parts if we carry that particular brand.

expert reply by: Jeff D

0

click to enlarge

Answer 1

We have several replacement parts for the internals of a Ram brand square jack. The Replacement Rod and Nut #TJD-12000-RODNUT will fit the following Ram jacks: #TJD-12000SP-F2 10K Sidewind with 12-3/8 inches of travel w/handle #TJD-12000SP-R2NH 10K…

view full answer...

Answer 2

The spring that comes with gear set #BD500212 for Bulldog 12K jacks is a compression spring. It keeps tension on the upper gear to help keep in place and aligned. I have included a picture that shows where the inner pieces go inside the jack.

view full answer...

Answer 3

Without the manufacturer name and model number of the jacks on your truck camper it will be difficult at best to determine the correct replacement parts for the jacks. I pulled this part from stock and attached a photo showing all of the dimensions…

view full answer...

Answer 4

Dico was actually purchased by Titan quite a while back. They did continue their line, however, and the Titan #T1755000 would be a good replacement option for the whole coupler end. That being said, if you just wanted to repair the coupler without a…

view full answer...

Answer 5

At capacity your trailer will weigh 6,000 lbs plus the weight of your trailer. You will need to pick a jack that can safely handle the maximum tongue weight that your trailer will see. Tongue weight is usually 10-15 percent of the total weight of the…

view full answer...

Answer 6

I confirmed with my contact at Dutton-Lainson that Replacement Miter Gear Kit for Dutton-Lainson Trailer Jacks - 1,250 - 2,000 lbs. (1996 and Newer) #DL22439 is your correct kit for your Dutton Lainson boat jack. We were able to match this gear kit…

view full answer...

Answer 7

It is likely based on the capacity of the jack that you will need bevel gear kit, #F0933302S00, that you have referenced. You may be able to find more information about the jack by looking at the cap or for numbers near the bottom of the inner/outer…

view full answer...

Answer 8

We do not offer a gear kit specifically for the Reese 74410 trailer jack but there is a good possibility that the Replacement Bevel Gear Kit for Fulton Jacks, #F0933302S00, will work for you. I have included a picture which lists the dimensions of…

view full answer...

Answer 9

I pulled the Fulton Bevel Gear Kit, #F0933302S00, from the warehouse and measured the bevel gears for you. The gears are 1-1/8 inches outer diameter x 15/32 inch thick with a 1/2 inch inner diameter. The groove pin is 3/16 of an inch in diameter x 1…

view full answer...

Answer 10

There are one Fulton Jack repair kit available that could potentially work for you. You will need to get some measurements from the gears in your jack in order to know which one would work for you. I attached a picture that has all of the dimensions…

view full answer...

Answer 11

Thank you for providing the photo of your Fulton jack handle as well as the clear description of the compatibility issue you've encountered with the jack repair kit you purchased, part #F0933302S00. My contact at Fulton was able to confirm that…

view full answer...