What is the Wheel Made of on Dutton-Lainson Easy Swivel Trailer Jack

Question

Question:

is this tire filled with air or solid?

asked by: Don S

0

Expert Reply:

The wheel on the Dutton-Lainson Pull Pin Easy Swivel Trailer Jack is solid and made a poly molded hard plastic so you won't have to worry about a flat tire. The tire can also be replaced with Replacement Wheel # DL22410

expert reply by: Erik B

0

Answer 1

Scissor jacks are designed for stabilizing, not lifting. I wouldn't recommend you use one as an A-frame jack. You might be better off with a side mounted jack like the part #DL22800 that can be positioned further back on the trailer frame for…

view full answer...

Answer 2

I went out to the warehouse and pulled Dutton Lainson trailer jack #DL22800 to take the measurements for you. The 3 holes closest together are 1 inch apart on center. From the third hole to the furthest away hole is 2-1/2 inches. Side to side the…

view full answer...

Answer 3

I went out into our warehouse and pulled a Dutton Lainson Jack #DL22800 to measure the distance from the bottom of the wheel to the center of the mounting bracket when retracted and found that distance to be 13 inches. Check out the video I attached…

view full answer...

Answer 4

These trailer jacks come pre-greased and must be disassembled to be greased when needed. Dis-assembly starts with removal of the cap at the top of the jack. I have provided a drawing that should help with dis-assembly and re-assembly.

view full answer...

Answer 5

If the copper wire has turned black, it will mean one of two things. First, salt water somehow got through the insulation/jacket, causing it to severely oxidize. Second, it overheated and actually burned some of that jacket. In either case, I highly…

view full answer...

Answer 6

We do have the replacement wheel you would need for your Dutton Lainson Jack part #DL22800. You would want the part #DL22410.

view full answer...

Answer 7

I spoke to a technical contact at Midwest Industries and he advised that they use 800-lb-rated trailer jacks supplied by Dutton-Lainson. I contacted Dutton-Lainson and found the 800-lb jack referred to uses replacement pull pin kit #DL22449. This kit…

view full answer...

Answer 8

There are some Dutton-Lainson trailer jacks that are made in the USA as well as a few that are not. Any jacks that we carry that are made in the USA have that as part of the description to help set them apart. Currently we have the following options:…

view full answer...

Answer 9

The reason why you do not see written instructions for repairs of jacks is the internal parts of a typical trailer jack are not end-user serviceable with the exception of the top gears. And with those it is just a matter of removing the old ones and…

view full answer...

Answer 10

I have 2 trailer jack options that are bolt-on, side frame mount jacks that will offer you lower retracted heights than the 15 inch retracted height of your existing Dutton-Lainson jack. One is a similar Dutton-Lainson jack and the other is a Fulton…

view full answer...

Answer 11

I can certainly provide those measurements for you! I spoke with my contact at Dutton-Lainson about the Pull Pin, Easy Swivel Trailer Jack #DL22800 and Replacement Wheel #DL22410. He confirmed that the inner bore of the wheel measures 0.645 inches.…

view full answer...

Answer 12

Usually, the jaw on the underside of a trailer coupler can be adjusted by tightening or loosening the nut on the underside of the jaw. If you loosen the jaw slightly, you should be able to get the coupler to come off the trailer ball. Once you get…

view full answer...

What is the Wheel Made of on Dutton-Lainson Easy Swivel Trailer Jack

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching