Does SuperChips FlashPaq F5 Programmer SU2847 Fit 2018 Chevy Silverado 1500 5.3 liter

Question

Question:

Will this product be compatible with a 2018 Silverado 1500 LT 5.3 l E assist with 8 speed? I have tried One of your Flash packs recently which was not compatible

asked by: Gary H

0

Expert Reply:

Yes we have confirmed with Superchips that the Flashpaq F5 part # SU2847 that you referenced is a confirmed fit for your 2018 Chevy Silverado 1500 5.3 liter and 8 speed transmission.

expert reply by: Jameson C

0

Answer 1

You will be able to use 87 octane with all of our performance tuners that are compatible with your 2017 Chevrolet Silverado, but not with all of the tunes they offer. If you are towing a light trailer, you can go with Chevrolet's recommended…

view full answer...

Answer 2

For your 2010 Chevy Avalanche with a 5.3 liter V8 we have the Edge Evolution #EP85350 that's a confirmed fit that can disable the AFM (active fuel management) system of your truck. It doesn't allow you to go in an manually adjust the timing…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Answer 5

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 6

My contact at Yates Rubber advises that a nominal 8-inch keel roller does not measure exactly 8 inches; typically they are slightly smaller than the specified size, much the way a piece of 2 x 4 lumber is not exactly 2-inches by 4-inches. I took…

view full answer...

Answer 7

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 10

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 11

The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…

view full answer...

Answer 12

In order to install a brake controller on a dump truck you'd first need to start with a 4-way trailer connector and then adapt this to a 7-way so you can hook up a brake controller. I won't have much info for anyone particular dump truck but…

view full answer...

Does SuperChips FlashPaq F5 Programmer SU2847 Fit 2018 Chevy Silverado 1500 5.3 liter

Product Page this Question was Asked From

Continue Researching