Will the Demco Lunette Ring Work on The Curt Channel Style Adjustable Ballmount

Question

Question:

will this Demco Lunette Ring - Adjustable Channel Mount - 3inch Diameter - Primed - 25,000 lbs Item # DM09557-97 fit the curt 45900 channel?

asked by: David W

0

Expert Reply:

Yes the Demco Lunette Ring part # DM09557-97 will work with the Curt Channel Style Adjustable Ballmount part # C45900. It will be rated for the 1,400 lb tongue weight and the 14,000 lb gross trailer weight rating of the Curt ball mount.

Replacement Shank for Curt Channel Style Adjustable Ball Mounts part # C45910 is an option as well with the same capacity.

expert reply by: Randy B

0

Answer 1

You should have no problem using the 2-Tang Clevis for BulletProof Hitches Adjustable Ball Mount item #358CLEVIS on your current ballmount. I say should because I have no idea which one you have but I do have the bolt hole measurements so you can…

view full answer...

Answer 2

Starting with the most significant difference here, the BulletProof Hitches Adjustable 2-Ball Mount #MD204 has a different rise/drop when compared to the Curt #C45900. The #MD204 has a 4" drop and a 4" rise while the #C45900 has a 6"…

view full answer...

Answer 3

The Dexter 2-Tang Clevis #T1807800 has mounting holes that will line up with the BulletProof Hitches 2-Ball Mount for 2-1/2" Hitches #MD254, but the Clevis uses 3/4" pins while the BulletProof shank uses 5/8" pins for the ball mount.…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Hi Joe, Yep, you heard correct, you can go from a 2 inch shank to a 2-1/2 inch shank with your Reese weight distribution hitch without issue. One of the following 2-1/2 inch shanks should have the right rise/drop for your application. Here are the…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 11

I recommend using the Curt Lock Set #C23556 for your Curt Adjustable 2-Ball Mount #C99NR. This comes with a lock for the hitch receiver and one for the ball mount platform. Even though your platform uses 2 pins, only 1 locking pin is needed to secure…

view full answer...

Answer 12

Hey George, thanks for reaching out! As long as you aren't towing more than the 3,400 lbs I recommend using the Hidden Hitch by Draw-Tite Trailer Hitch Receiver #DT82GR for your 2023 Volvo XC60 because of the completely removable hitch receiver…

view full answer...