Could Reese Fifth Wheel Rail Kit for 2008 Toyota Tundra Fit with Air Bag Kit

Question

Question:

I have air bags on my truck. 2008 Tundra 6 1/2 for bed. Will this work with the airbags.

asked by: Brooks M

0

Expert Reply:

That's harder to say without knowing which air bag kit you have on your truck but what you can do is compare the picture I attached of what the rail kit part # RP50084-58 to your air bag setup to see if the two kits would interfere.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Let's start with the hitch itself. If you have a long bed truck, the Reese, part #RP30928, would be an excellent choice, with its 20K capacity. For a short bed truck, you'll want to also use a rotating pin box to prevent the nose of your…

view full answer...

Answer 2

The rails in the bed of your pickup are installed so that the king pin will be just forward of the rear axle when hitched. The mounting location is vehicle specific and if you would like to provide your trucks year, make, model bed length and cab…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 6

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 7

Most fifth wheel rails are made to the same industry standard dimensions. They aren't all though. If you measure 22 inches on center between the two rails and they look like the rails of the #RP30035 that you referenced they would be the industry…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth mentioning…

view full answer...

Answer 10

The factory prep package or pucks are not the same between Ram, GM and Ford. The spacing is all different which means you cannot use a 5th wheel hitch for Ram pucks on a GM with pucks. Take the Curt A25 5th Wheel Trailer Hitch for example which is…

view full answer...

Answer 11

Having the puck system is a great feature. If you ever plan on loading the bed with mulch, sand or rock you'll quickly find that having rails permanently bolted to the bed floor is a real pain. Not only that, but the pucks look a lot better.…

view full answer...

Answer 12

Thank you for the photo of your 2016 Ram 3500's bed rail which sits 59-inches above ground. You are correct that the recommended minimum clearance between a bed rail and the underside of the trailer's overhang is 5 to 6-inches, as shown in…

view full answer...