Why Do Thread Forming Bolts for Reese Dual Cam Require Rivet Nuts

Question

Question:

Hello, Im confused. If the bolts are Thread Forming, then why the need for the Rivet Nuts? A thread forming bolt should form the threads in the metal as they as installed. Thanks,

asked by: Kevin P

0

Expert Reply:

I agree that calling the # 58437 thread forming is a little misleading since it's recommended that you drill holes in the frame and use the rivet nuts part # RP58507. Thread forming bolts typically have more of a drill bit on the end of the bolt than what the # 58437 have.

expert reply by: Jameson C

0

Answer 1

I reached out to my contact at Reese and you are correct that you will need new rivet nuts #RP58507 to install your Reese Dual Cam Weight Sway Control #RP26002 on your new trailer. He mentioned that the replacement thread forming screws #58437 can be…

view full answer...

Answer 2

The product weight of the Gen-Y Torsion 2-Ball Mount w/ Stacked Receivers #325-GH-1225 is 87 lbs. This hitch mount is awesome due to all the extra things you can use with it. It has 5 stacked 2" hitch receivers that can accommodate almost any…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 9

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 10

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 11

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 12

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...