What is Overall Width of Bristol Double RV Waste Valve # 34466NDHR19AAA

Question

Question:

What is the width of the valve

asked by: Keith O

0

Expert Reply:

The overall width of the Bristol Double RV Waste Valve # 34466NDHR19AAA will be 4-1/2 inches.

expert reply by: Jameson C

0

Answer 1

The Bristol Double RV Waste Valves - Elbow - Rotating - 3" and 1.5" Hubs to 3" Spigot, #34466ND14AAR is to be installed using the LaSalle Bristol ABS Solvent Cement - Black - 1/2 Pint #3447530889. These can be rotated to desired…

view full answer...

Answer 2

The Bristol Double RV Waste Valves #34466ND14AAR is about 9" long outside to outside. Attached is a photo showing this as well as a review video you can check out.

view full answer...

Answer 3

Yes, you can replace the 3" and 1-1/2" valves on your Bristol Double RV Waste Valves - Elbow - Rotating - 3" and 1.5" Hubs to 3" Spigot #34466ND14AAR with the Bristol Waste Valve Body for RV Gray Water w/ Coupler, Seals, and…

view full answer...

Answer 4

Per the manufacturer when measuring The Double RV Waste Valve #T85B the spigot to spigot dimensions 7.063 from side to side. The spigot is 1.920 inches from the back of the flange to the end of the spigot or 1.450 inches from the front side of the…

view full answer...

Answer 5

I took the outermost dimensions of the RV waste valve #T85. It's about 12 inches long, 4-1/2 inches wide, and 9-1/2 inches tall with the handle down or 13 inches with it up.

view full answer...

Answer 6

RV sewer valves like the Bristol #34466NDHR19AAA that you referenced are the same valves used by many of the OEM's including, sometimes, Winnebago. We do not have the ability pull build sheets and know exactly what part was installed on your…

view full answer...

Answer 7

The Valterra Double Elbow DWV Fitting, #D50-3047, measures 9 inches from end to end. Also, from the horizontal opening to the vertical opening the measurement is 7 inches.

view full answer...

Answer 8

ABS plastic like what the Bristol Double RV Waste Valves #34466NDHR19AAA you referenced is made of can be glued to ABS plastic but plumbing codes won't allow you to glue it to PVC. You can solvent weld this to ABS plastic though!

view full answer...

Answer 9

The Bristol Double RV Waste Valves, #34466NDHR19AAA has an overall measurement of 11-7/8" from edge to edge with a 9" measurement between the outer edge of each waste gate.

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 12

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

What is Overall Width of Bristol Double RV Waste Valve # 34466NDHR19AAA

Product Page this Question was Asked From

Continue Researching