Does the Curt 60633 Gooseneck Hitch Fit on the 2020 Ram 3500 Single Wheel Long Bed

Question

Question:

Will this hitch fit a 2020 ram 3500 single wheel long bed?

asked by: Lawrence

0

Expert Reply:

Yes. I was able to confirm with Curt, that their Curt Custom Underbed OEM-Style Gooseneck Hitch # C60633 is a confirmed fit on the 2020 Ram 3500.

expert reply by: Erik B

0

Answer 1

I went out to the warehouse and pulled the Replacement Hitch Ball for B&W Turnoverball Underbed Gooseneck Hitches, part #BWGNXA2000, and took some measurements for you. The square part of the hitch ball is 4" long and 2-1/2"…

view full answer...

Answer 2

The gooseneck hitch you have is the Curt 600 Series part #C60604 which is just the rail kit of the #C607-604 that you referenced. I attached a link to the install instructions and an install video for the hitch for you to check out as well. If your…

view full answer...

Answer 3

I had our warehouse measure the Curt Custom Underbed OEM-Style Gooseneck Trailer Hitch #C60633 you were looking at and it is 17" long x 9-1/4" wide x 3-3/8" deep as you can see in the included diagram. The Curt #C60633 is a…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 7

Hey Ted, so if you look in the bed of your truck and see 5 holes/pucks that would mean you have the OEM prep. I'd assume if you had it you'd have seen them by now. If you had it you'd only need a ball like the part #C60618. If you…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Eric, the Curt Multi-Fit Ball Kit w/ 4" Offset for Chevy/Ford/GMC/Nissan Underbed Gooseneck Hitch #C68ZV is not going to work with your Ram, unfortunately. This one is only going to work for select YMM (Year Make Model) Ford 250-450s, GMC…

view full answer...

Answer 10

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 11

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 12

Gen-Y's calculation for pin weight is a safe guess, but isn't the most accurate so the only way you'll get the correct capacity Gen-Y 5th Wheel Pin Box is to fully load the trailer and go to a commercial scale to measure the pin weight.…

view full answer...