Replacement Grease Seal and Bearings for 1992 Mastercraft Boat Trailer

Question

Question:

I have a 1992 mastercraft boat trailer and i was looking at the BK2-100 as the replacement. The trailer is calling for a 1.688x2.328x1/2inch wide seal and the BK2-100 seems to be a littler bigger at 1.719x2.565. Will this work or is there a better match? The races and bearings are correct.

asked by: Dan B

0

Expert Reply:

The correct grease seal for your Mastercraft boat trailer is part # 010-180-00. It has an inner diameter of 1.68" and an outer diameter of 2.33" to match the dimensions your mentioned required for your trailer axle.

You can then purchase the bearings and races individually:

Outer Bearing # L44649
Outer Race # L44610
Inner Bearing # L68149
Inner Race # L68111

I've included a quick link to the complete list of parts at the bottom of this page for you as well.

expert reply by: Carla M

0

Answer 1

Although we don't have a kit that includes the bearings/seal all in one package, you can certainly obtain the parts separately. You'll need: #25580 inner bearing and its #25520 race #LM67048 outer bearing and its #LM67010 race #21325…

view full answer...

Answer 2

Before you choose brakes or bearings you should verify what's currently on your trailer. If it is a 3,500 pound axle part #AKEBRK-35-SA will likely fit if the trailer has electric drum brakes. Both sides are included and labeled. They're also…

view full answer...

Answer 3

To replace the oil caps on your trailer, you can use the Kodiak XL ProLube Oil Bath Hub Body and Cap, 1.98 Inch #xlprolube1980. This oil cap replaces the body and cap, with the cap being made from a blue polycarbonate. Based on the outer diameter of…

view full answer...

Answer 4

Check out the picture I attached that shows the electrical connections that the Titan BrakeRite #T4813100 will make. I also attached installation instructions for this product for you to check out. The updated version of the Titan BrakRite is the…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

I definitely understand being a bit overwhelmed by the amount of options in front of you, however I can definitely help with differentiating the trailer hitches for your 2019 Subaru Outback Wagon along with explaining my personal recommendation,…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Replacement Grease Seal and Bearings for 1992 Mastercraft Boat Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching