Can Replacement Hardware be Ordered for Draw Tite Hitch # 65041

Question

Question:

Do you sell the hardware for this hitch?

asked by: Davis

0

Expert Reply:

We sell hardware for all of the hitches we offer with the part # RHK. To order hardware for the # 65041 you'd just need to select Draw Tite from the drop down menu and then enter the hitch part number in the part number box and you'd be set.

expert reply by: Jameson C

0

Answer 1

The Draw-Tite Front Mount Trailer Hitch Receiver #65041 is rated for up to 9,000 lbs line pull but you can honestly use whatever size winch you want to for your 2004 Toyota Tacoma. As long as you don't exceed the weight rating of the front mount…

view full answer...

Answer 2

I have a few different options for you, but the Draw-Tite Receiver #65041 is not going to fit a 1998 Toyota 4Runner. If you want to stick with the Draw-Tite brand, I recommend going with the Max-Frame Hitch Receiver #75091. It is a Class III hitch,…

view full answer...

Answer 3

You can check the frame on your 2001 Tacoma as shown in the attached instructions to see where a front mount hitch #C31013 and #65041 is installed. In the instructions it does state you have to remove the tow hooks and they will not be re-installed.…

view full answer...

Answer 4

We have not yet had a chance to test fit the Curt Front Mount Trailer Hitch part #C31013 on a vehicle specifically a Toyota Tacoma. So I would not be able to tell you exactly how much ground clearance is lost. However, I went out the warehouse and…

view full answer...

Answer 5

For your 2001 Toyota Tacoma we have the Draw Tite hitch part #75078 as realistically the easiest fitting hitch that is a confirmed fit. The bumper does need to temporarily come off but it's more of a time consuming aspect vs. a difficulty type…

view full answer...

Answer 6

You have done the right thing by reading the installation instructions. Since CURT Front Mount Receiver, #C31013, was not tested on vehicles with any type of grille guard, the only way to determine fit is to look at the instructions for both parts.…

view full answer...

Answer 7

Yes the Curt front mount trailer hitch #C31013 will fit your 2002 Toyota Tacoma 4x4 Double Cab. I have included a link to the installation instructions for you to view.

view full answer...

Answer 8

I checked with Curt and they told me that the overall width of the Curt front hitch #C31013 is 32.50 inches and the center to center hole dimension is 30 inches.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Can Replacement Hardware be Ordered for Draw Tite Hitch # 65041

Products Referenced in This Question

Continue Researching