How To Confirm Fit of the CE Smith Roller-Style Guide-Ons for Boat Trailers On Any Trailer

Question

Question:

Will this guides work on a 2001 Tennessee boat trailer for a 21.5 ft crestliner boat

asked by: Micahel J

0

Expert Reply:

I can't confirm fit of the CE Smith Roller-Style Guide-Ons for Boat Trailers part # CE27610 for any one particular trailer but what I can tell you is that so long as the frame is no more than 3" wide x 4-1/4" tall it will fit just fine.

expert reply by: Conner L

0

Answer 1

Although you may be able to get by with just using one set of 5 foot roller bunks, I am a firm believer that in this case more is better. Having rollers the entire length of your wood bunks will not only make the loading and unloading process easier…

view full answer...

Answer 2

I contacted Plews and the only suggestion they can give to remove a stuck cartridge is to try to remove it with a pair of pliers. They also mentioned their grease guns like part #L30100 are not compatible with Mystic grease cartridges. You also want…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 5

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 6

That spindle looks pretty well destroyed so best option is going to be to replace the axle. You are going to need to measure your current axles in a few places to get the correct one as we don't have access to what your numbers reference. You…

view full answer...

Answer 7

The Bargman 7-Way, RV-Style Connector #WG54006-043 referenced in your question uses the standard RV-style pin locations for its 7-Way connector. I have attached a diagram of these locations and their functions for you to check out. Wire colors will…

view full answer...

Answer 8

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 9

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 10

Your trailer looks awesome! The Road armor equalizers #LC696740 and Equa-Flex Cushioned Equalizers #LC279687 are both pretty similar in performance even though the Road Armor has two dampers. The main difference is the size of the equalizers. The…

view full answer...

Answer 11

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 12

For all intents and purposes, yes, the Fulton drop leg stabilizer jack SJL80300 is the same as the square leg jack you asked about: - Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs #SJ-R208 Different manufacturers but otherwise they…

view full answer...

How To Confirm Fit of the CE Smith Roller-Style Guide-Ons for Boat Trailers On Any Trailer

Product Page this Question was Asked From

Continue Researching