Replacement Gears for Solera Powered Awning

Question

Question:

i have 2020 keystone with a power awning, the awning does not move, the motor is turning. will the 353964 gear repair kit fir my motor. 672050 is the head assembly. thanks

asked by: Jeff F

0

Expert Reply:

I'll start out by saying that some factory awnings are not actually Solera awnings, so you'll want to confirm that you've got a Lippert Components Solera Power Awnings with a Venture motor number 591-70, which is Lippert # LC266149. If that is the motor you have on your powered awning, you can use the # LC353964 to replace the gears.

expert reply by: Erik B

0

Answer 1

I have just what you need to replace the LED light strip on your awning, the Awning LED Fabric Light Kits part #LC423331 which is cut to fit. This light strip will slide into the track you have now you'll just need to attach the two lead wires.

view full answer...

Answer 2

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 9

It is not uncommon for certain factory brake controllers to have issues with electric over hydraulic brakes. This would be the first we have heard of this issue with a 2023 Ford F-350, but it is possible that the brake controller in your ford is…

view full answer...

Answer 10

To get power to the controller of your Solera Smart Arm 12V Power RV Awning part #LC759404, you need to tap into an existing circuit, or run a power wire from the battery with an inline fuse holder, and a 15 amp fuse, like part #SWC9538, and part…

view full answer...

Answer 11

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...