Parts Needed to Install B&W Patriot in Bed of 2006 GMC Sierra

Question

Question:

We are ordering the B and W Patriot BWRVK3255 and was wondering if there are any other parts we need to add to our order? Truck already has rails.

asked by: Vickie

0

Expert Reply:

As long as your truck has industry standard bed rails installed in the bed like ones provided with the # BWRVR3200, all you'll need is the B&W # BWRVK3255 Patriot hitch. If you don't already have a 7-way installed in the truck bed, you can do so using part # C56000.

expert reply by: Mike L

0

Answer 1

Yes, the B&W Universal Base Rails and Installation Kit for 5th Wheel Trailer Hitches, #BWRVR3200 will fit the 2013 GMC Sierra with a short bed.

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 5

Most fifth wheel rails are made to the same industry standard dimensions. They aren't all though. If you measure 22 inches on center between the two rails and they look like the rails of the #RP30035 that you referenced they would be the industry…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 8

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth mentioning…

view full answer...

Answer 9

Hey Jay. It sounds like you are on the right track here because a sidewinder pin box will be your only option for pulling your 5th wheel since you have a short bed truck with the Rambox. That said, you are right that the Reese Sidewinder cannot be…

view full answer...

Answer 10

The Patriot Slider part #BWRVK3270 might be a bit more noisy than the Companion slider part #BWRVK3400 due to the increased number of mounting points, 4 at the corners vs. 1 in the center. Probably not that noticeable and certainly not something…

view full answer...

Answer 11

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 12

Thank you for the photo of your 2016 Ram 3500's bed rail which sits 59-inches above ground. You are correct that the recommended minimum clearance between a bed rail and the underside of the trailer's overhang is 5 to 6-inches, as shown in…

view full answer...