How To Use Dual Sway Control Bracket With Gen-Y Torsion 2-Ball Mount

Question

Question:

Hello, can I please have the specs on product # 325-GH-1226 and 325-GH-3001 .

asked by: Ciaran G

0

Expert Reply:

The Dual Sway Control Bracket for Gen-Y Adjustable Ball Mounts with 2" Receivers part # 325-GH-300-1 will attach to the bottom hitch ball on the Gen-Y Torsion 2-Ball Mount w/ Stacked Receivers part # 325-GH-1226 and then allow for sway control bars to be added, the Curt Friction Sway Control for Weight Distribution Systems part # 17200.

If this was not what you are asking please clarify which specs you are looking for.

expert reply by: Conner L

0

Answer 1

Yes, the Dual Sway Control Bracket for Gen-Y Adjustable Ball Mounts with 2" Receivers #325-GH-300-1 will work with a 2", and 2-5/16" double ball mount. This product is also compatible with all the GEN-Y Versa-Ball Mounts, like…

view full answer...

Answer 2

We do have an adapter for the Gen-Y adjustable ball mounts that allows it to be used with sway control with the part #325-GH-300-1.

view full answer...

Answer 3

Yes, but you would have to add the replacement 2-ball mount for the standard Gen-Y in order to secure the bracket. So what you would need is the following: - Gen-Y Phantom X Adjustable Ball Mount w/ Stacked Receivers for 2" Hitch - 10"…

view full answer...

Answer 4

Yes the Dual Sway Control Bracket #325-GH-300-1 that you referenced would work great with the Draw Tite sway control part #83660 that you mentioned.

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 7

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

Yes, the best option we can offer you to add fuel capacity is with the DeeZee Truck Bed Auxiliary Tank part #DZ91752X which should fit in the space you have between the cab and 5th wheel hitch no problem as it is only 9" deep. I don't have…

view full answer...

Answer 10

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 11

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 12

To determine which brake assemblies would be needed, you will need to measure your existing brake drums as shown in the provided photo. Since your trailer has a 14,000 lb capacity, you most likely have tandem 7,000 lb axles, which typically use a…

view full answer...