What Material is Valterra Plumbing Roof Vent Made of

Question

Question:

good morning, Im interesting in the Valterra vent code# va97zr. can I know what material is it? thanks !

asked by: Jimmy Y

0

Expert Reply:

The Valterra Plumbing Roof Vent # VA97ZR has a polypropylene construction. This is a thermoplastic polymer which is basically a fancy way of saying that it's essentially plastic.

expert reply by: Jon G

0

Answer 1

I do have options for you but I called my contact at Camco and they told me that the top part on the Cyclone RV Plumbing Vent part #CAM40597 that rotates is not designed to be removed. I went out to our warehouse and tested this myself to confirm…

view full answer...

Answer 2

The main piece that attaches to the pipe is what gets screwed onto the pipe using the 3 included self-tapping screws. So you would insert the Cyclone RV Plumbing Vent #CAM40597 into the existing pipe on the roof and then use the screws through it and…

view full answer...

Answer 3

You would have to come up with a way to plug the CAM40597 when you didn't want it to be active. It's initial design is for venting plumbing so it doesn't have any type of on/off setting. It shouldn't pull in rain but if an insect…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 6

Thanks for the pictures of your roof vent lid Marty! Based on that the correct replacement is the Ventline part #BVD0449-A01 that you referenced if you wanted white or the part #BVD0449-A03 for the same smoke color you have now.

view full answer...

Answer 7

The B&W Companion OEM 5th Wheel Hitch w/ Slider for Chevy/GMC Towing Prep Package #BWRVK3775 you're looking at will work fine with your new Chevrolet Silverado. This hitch has 3 height adjustments so you'll be able to set the hitch height…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Hey Frankie, The bracket for the Timbren Suspension Enhancement System #TFR250SDJ has a locknut in it that makes it feel like the bolt (part #4) is fully tightened when it's not. Their techs have stated that you just have to push past this point…

view full answer...

Answer 10

For the front legs of a Lippert Ground Control 3.0 kit the replacement front jack leg solution you'd need is the part #LC362485. This will allow you to reuse your current motor and bracket. There isn't a gear replacement kit for the jack…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Hey David, we've used the LaSalle Bristol RV Roof Vent install kit part #344270KITW to install several MaxxFan RV roof vents and it's worked well so it would also work well for you. This comes with everything needed so it would be a great…

view full answer...

What Material is Valterra Plumbing Roof Vent Made of

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching