How Does the Cyclone RV Plumbing Vent Install

Question

Question:

Does it get attached with the screws to the pipe or roof

asked by: Charles H

0

Expert Reply:

The main piece that attaches to the pipe is what gets screwed onto the pipe using the 3 included self-tapping screws. So you would insert the Cyclone RV Plumbing Vent # CAM40597 into the existing pipe on the roof and then use the screws through it and the roof pipe to hold it in place. I have linked a video review of this vent for you.

expert reply by: Michael H

0

Answer 1

I do have options for you but I called my contact at Camco and they told me that the top part on the Cyclone RV Plumbing Vent part #CAM40597 that rotates is not designed to be removed. I went out to our warehouse and tested this myself to confirm…

view full answer...

Answer 2

The Valterra Plumbing Roof Vent #VA97ZR has a polypropylene construction. This is a thermoplastic polymer which is basically a fancy way of saying that it's essentially plastic.

view full answer...

Answer 3

You would have to come up with a way to plug the CAM40597 when you didn't want it to be active. It's initial design is for venting plumbing so it doesn't have any type of on/off setting. It shouldn't pull in rain but if an insect…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 11

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...