In Bed Trailer Wiring to Tow Gooseneck Trailer with 2007 Dodge Ram 1500

Question

Question:

I am looking for a wiring harness. I have a 2007 Dodge Ram 1500 4x4 with a factory 7 pin trailer hook up. I purchased a Curt Goose neck hitch from you and I am looking for harness that will allow me to use my original 7 pin for a bumper trailer and the also go to a 7 pin that will mount in my truck box.

asked by: Jason S

0

Expert Reply:

We have exactly what you need with part # HM42137.

It plugs inline with your 2007 Dodge Ram's factory 7-way so you keep the original connector and can add thi one into your truck's bed to hook up your gooseneck trailer.

expert reply by: Charles S

0

Answer 1

There isn't necessarily 'one' correct spot. Typically, folks will install the connector so it's on the driver's side behind the wheel well. If you click the provided link, you can see a typical installation of a similar wiring…

view full answer...

Answer 2

You will need the Hopkins Endurance 5th Wheel/Gooseneck 90-Degree Wiring Harness with 7-Pole Plug Item #HM42137, for your 2006 Dodge Ram 2500. This harness will fit your 2006 Dodge Ram 2500 with a factory installed 7-Way connector. It will plug in…

view full answer...

Answer 3

Thanks for all the information and the picture! I would be happy to help you set up your 2019 Ford Escape to tow your new Aliner Expedition Camper. I did some research to confirm but your camper has the standard 7-way connector. 9-pin connectors are…

view full answer...

Answer 4

I have spoken to Tuson about this issue and there is no way to tell beforehand if the intermittent vehicle OBD network connection will happen, unfortunately. However, as you have a 2003 Ram 3500 and this is listed as being a problem with some Ram…

view full answer...

Answer 5

The Hopkins 5th wheel wiring harness #HM42137 acts as a T-connector. It will provide a 7-way trailer connector in the bed of your truck while retaining the one at the back too. This fits all 2008 Dodge trucks with factory installed 7-way connectors.

view full answer...

Answer 6

For a larger alternator like what you have we have the Redarc Smart Start Battery Isolator #331-SBI212 which is rated for up to 200 amps. With this battery isolator, you can transfer power from your start battery to an auxiliary battery without…

view full answer...

Answer 7

As long as you get the voltages to match up correctly you can add a 12 volt battery to a battery bank with the TorkLift HiddenPower Under-Vehicle Battery Mount with Battery Box #TLA7740. The key is knowing the difference between running the batteries…

view full answer...

Answer 8

In order to prevent draining your main battery when using an inverter at night, I recommend using the Deka Battery Isolator, #DW08771, with the TorkLift HiddenPower Under-Vehicle Battery Mount with Battery Box, #TLA7740, (battery not included). The…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...