How Does Hitch Install on 2018 Chevy Equinox Diesel Fit with Urea Tank

Question

Question:

How do you install reciever when there is a reservoir mounted on frame in that area

asked by: Billy W

0

Expert Reply:

When installing the Draw Tite hitch part # 76217 that you referenced on your 2018 Chevy Equinox diesel model the urea tank you mentioned gets temporarily removed. For more info on that I attached a picture from the install instructions that covers this step as well as a link to the install instructions and a link to an install video on a similar Equinox.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 6

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 7

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way…

view full answer...

Answer 10

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has…

view full answer...

Answer 11

A ST205/75R14 trailer tire is going to have a diameter of about 26.3" and a width of 8.1" when inflated. If we go up to a 15", the ST205/75R15 tires are about 27.3" in diameter and 8.1" wide. So, they have…

view full answer...

Answer 12

I do have a solution for your 2024 Kia Telluride that has the LED taillights that does allow it to have both a 4-way and 7-way plus install a brake controller but it is not with the #TK74CR which does not work for you based on the LED taillights.…

view full answer...