What Is the Outside Diameter of the LaSalle Bristol RV Sewer Slip Hub with Flange 34466V13

Question

Question:

Hello, I removed a cracked flange like this that slips into my black tank where the valve attaches. Can you tell me the OD of pipe as that what slips in male fitting to female spout on black tank. Thanks,

asked by: Lucuis D

0

Expert Reply:

The LaSalle Bristol RV Sewer Slip Hub with Flange part # 34466V13 has an outer diameter of 3-3/16". That said, this adapter has a hub style connection which means it is designed so that a 3" diameter pipe can slide into the orifice.

expert reply by: Conner L

0

Answer 1

If the sewer line you have is a 3 inch sewer line that slips into the both sides of the valve you have now the part #34466N4BB72GM will fit and work well. You will need to use ABS solvent like #3447530889 to install it as well. If instead one side…

view full answer...

Answer 2

The depth of the 3" tube to the flange on the LaSalle Bristol RV Lug Adapter with Flange #34466V13B is approximately 1-1/4" deep. The Valterra RV Sewer Lug Fitting with Flange #T1009 has a 1-1/8" depth, which is the only difference…

view full answer...

Answer 3

The LaSalle Bristol RV Sewer Slip Hub with Flange - 3" #34466V13 you were looking at will work with the 3" ABS drain pipe on your RV. The hub side will bolt to your black water waste valve that you mentioned. You will also need the LaSalle…

view full answer...

Answer 4

What I think you are asking is if you can replace within a current system, a valve assembly of one manufacturer with that of another. Yes, the fitment of valve assemblies is industry standard in dimensions. A Valterra 3" can be replaced with a…

view full answer...

Answer 5

In order to install a new Cable Actuator RV Waste Valve #34466N4AB96GMA, you're likely going to need to cut off the pipes at the spigot and hub in order to install the new waste valve. It's more than likely that ABS sealant was used to weld…

view full answer...

Answer 6

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 7

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 8

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 9

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

I do have an option but Glo-Brite is no longer in business so you won't be able to get any replacement parts for these lights such as lenses. The only option you have would be a full replacement for which the most similar option we offer is the…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

What Is the Outside Diameter of the LaSalle Bristol RV Sewer Slip Hub with Flange 34466V13

Product Page this Question was Asked From

Continue Researching