Can Triple Axle Hanger kit part # APTT5 be Used on Trailer with 7k Axles

Question

Question:

Hello, Im building a gooseneck trailer. I have three 7000 lbs axels. Will APTT5 work instead of the APTT1?

asked by: Zachary H

0

Expert Reply:

Yes, the Triple Axle Hanger kit part # APTT5 would work great on your trailer that has 7k axles as it was designed for use on axles up to 7k.

expert reply by: Jameson C

0

Answer 1

In order to determine the correct leaf spring hanger locations on a trailer you first need to position the axles correctly. I have attached a help article on this part of the process for you. Then, once the axles are correctly positioned you can then…

view full answer...

Answer 2

If your shackles and equalizers are flipping upside down that would indicate you have either too wide of hanger spacing or you have equalizers that are too short. The easy solution will be to get the dimensions of your equalizer to me so that I can…

view full answer...

Answer 3

Some movement is normal. This is because there are two pivot points, one at the second hanger and one at the third hanger which are on either side of the center axle. What you will want to do is check several things to determine if there is wear that…

view full answer...

Answer 4

The differences are the dimensions of the hangers and equalizers of the three kits. The #APTT1 uses totally straight equalizers and taller center hangers. The #APTT3 uses more traditional sized equalizers and center and outside hangers that differ in…

view full answer...

Answer 5

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 6

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 7

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Can Triple Axle Hanger kit part # APTT5 be Used on Trailer with 7k Axles

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching