Dimensions of Brophy Pintle Hook For 2-1/2" Hitches

Question

Question:

What is the dimension from the pin center to the bottom of the u shape pintle

asked by: Daniel

0

Expert Reply:

The Brophy Pintle Hook for 2-1/2" Hitches part # BR27FR measures 9" from the center of the pin hole to the center of the U-shape pintle hook. It measures 12" from the center of the hitch pin hole to outer most portion of the pintle hook.

expert reply by: Heather A

0

click to enlarge

Jesse T.

4/30/2024

do you happen to have a measurement from the pin to where it changes from the pintle to the receiver stock to the pin hole

Reply

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 3

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 4

The centerline on the #BR27FR is going to be from the center of the hitch pin hole. If you draw a line straight out and measure the distance to the bottom of the hook that is 1". I have attached a diagram below for your reference.

view full answer...

Answer 5

Yes, the Sleeve-Lock Trailer Coupler #CTA-196 will fit the channel bracket that comes with the Brophy Lunette Ring w/ 3-Position Adjustable Channel Bracket #BR43ZR. The bolt holes match as well when it comes to size and spacing so you'll be good…

view full answer...

Answer 6

The Brophy Pintle Hook part #BR27FR will accept any lunette ring with an inner diameter equal to or greater than 2-1/2" which will have a thickness of 1-1/2". This is the correct way to determine compatibility between a pintle hook and…

view full answer...

Answer 7

The wiring color codes and wire gauge recommendations for the Pollak Heavy-Duty, 7-Pole, Round Pin, Trailer Wiring Connector, item #PK11700, are listed below. White - Ground Return - 8 gauge Black - Clearance, Side Marker, Identification - 12 gauge…

view full answer...

Answer 8

The Replacement Inner Slide Channel for Dexter Model 6 #T4846500183 has a shank that measures 3" wide x 2-1/2" tall to it's a little smaller than the 3" square shank that comes on the Replacement Inner Slide for Demco DA91…

view full answer...

Answer 9

You can expect the installation of the #C59236 in the 2023 Palisade video to be almost identical to your 2022 Hyundai Tucson. I'm not sure if the tail light style varies so removal may be a little different but the rest will be the same.

view full answer...

Answer 10

Pintle hitches are made to fit certain sized Lunette rings. The rings that we carry are only available in 2-1/2" or 3" diameter sizes. For example, the Curt Pintle Hook for 2" Hitches #C48004 fits lunette ring couplers with a minimum…

view full answer...

Answer 11

The Brophy Pintle Hook for 2-1/2" Hitches - 36,000 lbs #BR27FR is a very sturdy hitch with a nice powder coat finish. It is definitely heavy duty weighing about 20 lbs and designed for large vehicles with a 2-1/2 inch hitch receiver. It is rated…

view full answer...

Dimensions of Brophy Pintle Hook For 2-1/2" Hitches

Product Page this Question was Asked From

Continue Researching