Trailer Deck Height Range for 96" Long Gen-Y Hitch Aluminum Loading Ramp Set

Question

Question:

what is the max heigh the ramps can be lifted of the ground?

asked by: Daye

0

Expert Reply:

The range of height for the Gen-Y Hitch Aluminum Loading Ramp Set - 96" Long x 15" Wide - 10,000 lbs # 325-GH-R96 is 20" - 36". This would be from the ground to the deck.

I confirmed this with my contact at Gen-Y.

expert reply by: Jon G

0

Answer 1

I have another option for you, but due to the length of the ramp you would not want to use the Aluminum Car Hauler Ramp Set - 48" x 14-1/2" #288-07501 any higher than 12" as it could cause the ramp to not be secure and will be a pretty…

view full answer...

Answer 2

For a ramp used to load vehicles, it is important to have a high maximum weight capacity. With that being said, I recommend the Gen-Y Hitch Aluminum Loading Ramp Set - 144" Long x 15" Wide - 8,000 lbs #325-GH-R96. The Gen-Y Hitch Aluminum…

view full answer...

Answer 3

I do have a solution for you, but the Aluminum Car Hauler Ramp Set #288-07503 that you referenced has a max height of 16" for loading equipment. I did speak with my contact at Gen-Y Hitch who said that their aluminum loading ramps don't have…

view full answer...

Answer 4

I do not think the Aluminum Car Hauler Ramp Set - 72" x 14-1/2" - 6,000 lbs - Qty 2 #288-07503 would be the safest set of ramps for this particular job. They can handle the weight of the car no problem but looking at the picture you…

view full answer...

Answer 5

The best loading ramps we offer for vehicles with low ground clearance are the Gen-Y Hitch Aluminum Loading Ramp Set like part #325-GH-R96 which are 8' long. Therefore they should allow for a very shallow approach angle. These ramp are also…

view full answer...

Answer 6

The Gen-Y Hitch Aluminum Loading Ramp Set - 96" Long x 15" Wide #325-GH-R96 have a combined weight capacity of 10,000 lbs. As long as your Crown C-5 forklift does not exceed this weight capacity they will be able to handle the 10K weight.…

view full answer...

Answer 7

I checked with Gen-Y and they informed me that their ramp set part #325-GH-R96 is made from a double hollow tube, 3” x 5”, with a wall thickness of .125 A6063 alloy. This includes the hook end of the ramps as well.

view full answer...

Answer 8

For a Bobcat 331 that weighs up to 7,500 lbs I'd recommend the 10k ramps part #325-GH-R96 that you referenced which are 96 inches long and 15 inches wide. I attached a picture of a heavier tractor being loaded with these ramps as well as a review…

view full answer...

Answer 9

I may have a solution for you, but we don't have the CargoSmart Arched Loading Ramp Set - Non-Folding - Aluminum - 90" x 12" - 3,000 lbs #3483070 in a non-arched ramp. The only available flat ramp we have in close to 90" is the…

view full answer...

Answer 10

I checked with Gen-Y and they informed me that their ramp set part #325-GH-R96 is made from a double hollow tube, 3” x 5”, with a wall thickness of .125 A6063 alloy.

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...